1. //
  2. Start
  3. //
  4. Publications
  5. //
  6. Browse
  7. //

Browse by research area

301 - 350 out of 1,666Page size: 50

  1. A robust sliding mode control of a hybrid hydraulic piezo actuator for camless internal combustion engines

    Mercorelli, P., Werner, N., Becker, U. & Harndorf, H., 2011, 2011 IEEE/ASME International Conference on Advanced Intelligent Mechatronics, AIM 2011. IEEE - Institute of Electrical and Electronics Engineers Inc., p. 499-504 6 p. 6027099. (IEEE/ASME International Conference on Advanced Intelligent Mechatronics, AIM).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  2. A switching observer for sensorless control of an electromagnetic valve actuator for camless internal combustion engines

    Mercorelli, P., 2011, 2011 50th IEEE Conference on Decision and Control and European Control Conference, CDC-ECC 2011. IEEE. C. S. S. & E. U. C. A. (eds.). IEEE - Institute of Electrical and Electronics Engineers Inc., p. 946-951 6 p. 6161316. (Proceedings of the IEEE Conference on Decision and Control).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  3. A switching model predictive control for overcoming a hysteresis effect in a hybrid actuator for camless internal combustion engines

    Mercorelli, P., 2011, PRECEDE 2011 - Workshop on Predictive Control of Electrical Drives and Power Electronics. IEEE - Institute of Electrical and Electronics Engineers Inc., p. 10-16 7 p. 6078681. (PRECEDE 2011 - Workshop on Predictive Control of Electrical Drives and Power Electronics).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  4. Published

    Localization of Passengers Inside Intelligent Vehicles by the Use of Ultra Wideband Radars

    Galdia, P., Carsten, K. & Georgiadis, A., 2011, Signal processing, image processing and pattern recognition: international conference, SIP 2011. Kim, T., Adeli, H., Ramos, C. & Kang, B-H. (eds.). Springer, p. 92-102 11 p. (Communications in Computer and Information Science; vol. 260 CCIS).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  5. Published

    Assessment of pharmaceutical waste management at selected hospitals and homes in Ghana

    Sasu, S., Kümmerer, K. & Kranert, M., 06.2012, In: Waste Management & Research. 30, 6, p. 625-630 6 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  6. Published

    Transformation products of pharmaceuticals in surface waters and wastewater formed during photolysis and advanced oxidation processes: Degradation, elucidation of byproducts and assessment of their biological potency

    Fatta-Kassinos, D., Vasquez, M. & Kümmerer, K., 10.2011, In: Chemosphere. 85, 5, p. 693-709 17 p.

    Research output: Journal contributions › Scientific review articles › Research

  7. Published

    Aesthetic Design of Masonry Arch Bridges

    Ohler, A. & Kirschner, U., 2010, Proceedings of the Eight International Masonry Conference 2010. Jäger, W., Haseltine, B. & Fried, A. (eds.). The Masonry Society, p. 383-392 9 p. (Masonry : Proceedings of the British Masonry Society; vol. 11).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  8. Published

    Polymer-Nanofasern und metallische Nano-Drähte: Aktuator- und/oder Sensorelement sowie Struktur und Manschette diese aufweisend ; Aktenzeichen DE 10 2010 022 067.1

    Georgiadis, A. & Schimmack, M., 01.12.2011, Deutsches Patent- und Markenamt, Patent No. DE102010022067A1, 31.05.2010

    Research output: Patents › Patent

  9. Published

    Geometrical Characterization of Polyethylene Oxide Nanofibers by Atom Force Microscope and Confocal Laser Scanning Microscope

    Fuhrhop, C. & Georgiadis, A., 30.06.2011, FiberMad 11, International Conference on Fibrous Products in Medical and Health Care . Talvenmaa, P. (ed.). Tampere University of Technology, 7 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research

  10. Published

    Sensormikrosysteme zur Überwachung der Atemluftqualität basierend auf Polymer Nanofasern

    Fuhrhop, C., Georgiadis, A., Madeira Noguiera, C. & Ivanova, T., 2010, Sensoren und Messsysteme 2010: Vorträge der 15. ITG/GMA-Fachtagung vom 18. bis 19. Mai in Nürnberg. 1. ed. VDE Verlag GmbH, 7 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  11. Published

    Automated Measurement of Thread Quality

    Schlote, J., Werner, S., Georgiadis, A. & Lange, D., 06.2011, Sensor + Test: Nürnberg Exhibition Centre, Germany, 7. - 9.6.2011 ; [including] SENSOR 2011, 15th International Conference on Sensors and Measurement Technology, OPTO 2011, photonic metrology, 10th International Conference on Optical Technologies for Sensing and Measurement, IRS2 2011, 12th International Conference on Infrared Sensors & Systems ; short proceedings. AMA. F. F. S. E. V. (ed.). AMA Service, Vol. 1. p. 190 1 p.

    Research output: Contributions to collected editions/works › Published abstract in conference proceedings › Research › peer-review

  12. Published

    A Method to Enhance the Accuracy of Time of Flight Measurement Systems

    Papadoudis, J., Georgiadis, A., Koch, C. & Klein, S., 2011, Sensor + Test: short proceedings ; conferences 2011, Nürnberg Exhibition Centre, Germany, 7. - 9.6.2011 ; an event of the AMA Association for Sensor Technology. AMA. S. G. (ed.). AMA Service, Vol. 1. p. 211 1 p.

    Research output: Contributions to collected editions/works › Published abstract in conference proceedings › Research › peer-review

  13. Compound forging of hot-extruded steel-reinforced aluminum parts

    Pfeiffer, I., Foydl, A., Kammler, M., Matthias, T., Kosch, K. G., Jäger, A., Khalifa, N. B., Tekkaya, A. E. & Behrens, B. A., 11.2012, Proceedings of the 14th International Conference on Metal Forming, METAL FORMING 2012. Wiley-VCH Verlag, Vol. SPL. ISSUE. p. 159-162 4 p. (Steel Research International).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  14. Ion release from magnesium materials in physiological solutions under different oxygen tensions

    Feyerabend, F., Drücker, H., Laipple, D., Vogt, C., Stekker, M., Hort, N. & Willumeit, R., 01.2012, In: Journal of Materials Science: Materials in Medicine. 23, 1, p. 9-24 16 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  15. Mechanical and corrosion properties of as-cast and extruded MG10GD alloy for biomedical application

    Maier, P., Müller, S., Dieringa, H. & Hort, N., 2012, Magnesium Technology 2012 - Held During TMS 2012 Annual Meeting and Exhibition. Mathaudhu, S., Sillekens, W. & Neelameggham, N. (eds.). The Minerals, Metals & Materials Society, p. 253-259 7 p. (Magnesium Technology).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  16. Microstructure and mechanical properties of high pressure die cast AM50 magnesium alloy containing Ce

    Mert, F., Özdemir, A., Kainer, K. U. & Hort, N., 2012, Magnesium Technology 2012 - Held During TMS 2012 Annual Meeting and Exhibition. Mathaudhu, S. N., Sillekens, W. H., Neelameggham, N. R. & Hort, N. (eds.). The Minerals, Metals & Materials Society, p. 149-154 6 p. (Magnesium Technology).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  17. Microstructure and creep properties of MEZ magnesium alloy processed by thixocasting

    Morales Garza, E. D., Dieringa, H., Hort, N. & Kainer, K. U., 2012, Magnesium Technology 2012 - Held During TMS 2012 Annual Meeting and Exhibition. Mathaudhu, S. N., Sillekens, W. H., Neelameggham, N. R. & Hort, N. (eds.). Cham: Springer Schweiz, p. 385-389 5 p. (Magnesium Technology).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  18. Texture evolution during hot deformation processing of Mg-3Sn-2Ca-0.4Al alloy

    Dharmendra, C., Rao, K. P., Prasad, Y. V. R. K., Hort, N. & Kainer, K. U., 2012, Magnesium Technology 2012 - Held During TMS 2012 Annual Meeting and Exhibition. Mathaudhu, S. N., Sillekens, W. H., Neelameggham, N. R. & Hort, N. (eds.). The Minerals, Metals & Materials Society, p. 295-300 6 p. (Magnesium Technology).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  19. The formation of Sr 6.33Mg 16.67Si 13 in magnesium alloy AM50 and its effect on mechanical properties

    Fechner, D., Hort, N., Blawert, C., Dieringa, H., Störmer, M. & Kainer, K. U., 07.2012, In: Journal of Materials Science. 47, 14, p. 5461-5469 9 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  20. Corrosion behaviour of a nominally high purity Mg ingot produced by permanent mould direct chill casting

    Qiao, Z., Shi, Z., Hort, N., Zainal Abidin, N. I. & Atrens, A., 08.2012, In: Corrosion Science. 61, p. 185-207 23 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  21. Identification of unexpected hydrides in Mg-20 wt% Dy alloy by high-brilliance synchrotron radiation

    Gan, W., Huang, Y., Yang, L., Kainer, K. U., Jiang, M., Brokmeier, H. G. & Hort, N., 02.2012, In: Journal of Applied Crystallography. 45, 1, p. 17-21 5 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  22. Hot deformation behavior of Mg-2Sn-2Ca alloy in as-cast condition and after homogenization

    Rao, K. P., Prasad, Y. V. R. K., Suresh, K., Hort, N. & Kainer, K. U., 30.08.2012, In: Materials Science and Engineering A. 552, p. 444-450 7 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  23. Development of high performance single-phase solid solution magnesium alloy at low temperature

    Peng, Q., Huang, Y., Kainer, K. U. & Hort, N., 03.2012, In: Advanced Engineering Materials. 14, 3, p. 178-184 7 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  24. Effects of corrosion environment and proteins on magnesium corrosion

    Yang, L., Hort, N., Willumeit, R. & Feyerabend, F., 08.2012, In: Corrosion Engineering Science and Technology. 47, 5, p. 335-339 5 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  25. High ductile as-cast Mg-RE based alloys at room temperature

    Peng, Q., Huang, Y., Kainer, K. U. & Hort, N., 15.09.2012, In: Materials Letters. 83, p. 209-212 4 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  26. Influence of ageing treatment on microstructure, mechanical and bio-corrosion properties of Mg-Dy alloys

    Yang, L., Huang, Y., Feyerabend, F., Willumeit, R., Kainer, K. U. & Hort, N., 09.2012, In: Journal of the Mechanical Behavior of Biomedical Materials. 13, p. 36-44 9 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  27. Polycrystalline and amorphous MgZnCa thin films

    Schlüter, K., Zamponi, C., Hort, N., Kainer, K. U. & Quandt, E., 10.2012, In: Corrosion Science. 63, p. 234-238 5 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  28. Metallurgical characterization of hot tearing curves recorded during solidification of magnesium alloys

    Huang, Y. D., Wang, Z., Srinivasan, A., Kainer, K. U. & Hort, N., 01.09.2012, In: Acta Physica Polonica A. 122, 3, p. 497-500 4 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  29. Influence of cerium additions on the corrosion behaviour of high pressure die cast AM50 alloy

    Mert, F., Blawert, C., Kainer, K. U. & Hort, N., 12.2012, In: Corrosion Science. 65, p. 145-151 7 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  30. Hot working mechanisms and texture development in Mg-3Sn-2Ca-0.4Al alloy

    Dharmendra, C., Rao, K. P., Prasad, Y. V. R. K., Hort, N. & Kainer, K. U., 15.10.2012, In: Materials Chemistry and Physics. 136, 2-3, p. 1081-1091 11 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  31. Hot tearing susceptibility of magnesium-gadolinium binary alloys

    Srinivasan, A., Wang, Z., Huang, Y., Beckmann, F., Kainer, K. U. & Hort, N., 12.2012, In: Transactions of the Indian Institute of Metals. 65, 6, p. 701-706 6 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  32. Hot deformation mechanisms in AZ31 Magnesium Alloy Extruded at different temperatures: Impact of Texture

    Rao, K. P., Prasad, Y. V. R. K., Dzwonczyk, J., Hort, N. & Kainer, K. U., 01.09.2012, In: Metals. 2, 3, p. 292-312 21 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  33. Ultrasonic stirring as a production process for nanoparticle reinforced magnesium alloys and the compression creep response of ZE10 reinforced with ceria nanoparticles

    Dieringa, H., Hort, N. & Kainer, K. U., 2012, ECCM 2012 - Composites at Venice, Proceedings of the 15th European Conference on Composite Materials. European Society for Composite Materials, ESCM, 8 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  34. Manufacture of profiles with variable cross-sections, curvatures and twistings by influencing the material flow in hot extrusion

    Selvaggio, A., Ben Khalifa, N., Chatti, S. & Tekkaya, A. E., 2012, Proceedings of the 14th International Conference on Metal Forming, METAL FORMING 2012: Proceedings of the 14th International Conference on Metal forming. Kusiak, J. (ed.). John Wiley & Sons Ltd., Vol. SPL. ISSUE. p. 507-510 4 p. (Steel Research International; vol. 83.2012).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research

  35. Numerical approach for the evaluation of seam welding criteria in extrusion processes

    Schwane, M., Kloppenborg, T., Reeb, A., Ben Khalifa, N., Brosius, A., Weidenmann, K. A. & Tekkaya, A. E., 2012, Material Forming ESAFORM 2012: Proceedings. Merklein, M. & Hagenah, H. (eds.). Trans Tech Publications, Vol. 504-506. p. 517-522 6 p. (Key Engineering Materials; vol. 504-506).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  36. Experimental and numerical analysis of material flow in porthole die extrusion

    Kloppenborg, T., Schwane, M., Ben Khalifa, N. & Tekkaya, A. E., 2012, International Conference on Extrusion and Benchmark 2011: Progress in Extrusion Technology and Simulation of Light Metal Alloys. Tomesani, L. & Donati, L. (eds.). Trans Tech Publications, Vol. 491. p. 97-104 8 p. (Key Engineering Materials; vol. 491).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  37. New concepts for cooling of extrusion dies manufactured by rapid tooling

    Hölker, R., Jäger, A., Ben Khalifa, N. & Tekkaya, A. E., 2012, International Conference on Extrusion and Benchmark 2011: Progress in Extrusion Technology and Simulation of Light Metal Alloys. Tomesani, L. & Donati, L. (eds.). Trans Tech Publications, Vol. 491. p. 223-232 10 p. (Key Engineering Materials; vol. 491).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  38. Effect of Porthole Design and Welding Chamber Dimensions on Material Flow and Weld Deformability of Extruded Aluminium Profiles

    Lorenzo, D., Ben Khalifa, N., Tomesani, L. & Tekkaya, A. E., 2012, Material Forming ESAFORM 2012. Merklein, M. & Hagenah, H. (eds.). Trans Tech Publications, Vol. 504-506. p. 523-528 6 p. (Key Engineering Materials; vol. 504-506).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  39. Lightweight construction by means of profiles

    Chatti, S., Pietzka, D., Ben Khalifa, N., Jäger, A., Selvaggio, A. & Tekkaya, A. E., 2012, Material Forming ESAFORM 2012. Merklein, M. & Hagenah, H. (eds.). Trans Tech Publications, Vol. 504-506. p. 369-374 6 p. (Key Engineering Materials; vol. 504-506).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  40. High quality extrudates from aluminum chips by new billet compaction and deformation routes

    Misiolek, W. Z., Haase, M., Ben Khalifa, N., Tekkaya, A. E. & Kleiner, M., 01.01.2012, In: CIRP Annals - Manufacturing Technology. 61, 1, p. 239-242 4 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  41. Improving mechanical properties of chip-based aluminum extrudates by integrated extrusion and equal channel angular pressing (iECAP)

    Haase, M., Ben Khalifa, N., Tekkaya, A. E. & Misiolek, W. Z., 30.03.2012, In: Materials Science & Engineering A. 539, p. 194-204 11 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  42. Model based logistic monitoring for supply and assembly processes

    Münzberg, B., Schmidt, M., Beck, S. & Nyhuis, P., 09.2012, In: Production Engineering. 6, 4-5, p. 449-458 10 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  43. Simulation based comparison of safety-stock calculation methods

    Schmidt, M., Hartmann, W. & Nyhuis, P., 01.01.2012, In: CIRP Annals - Manufacturing Technology. 61, 1, p. 403-406 4 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  44. Published

    Materialbereitstellung in der Montage

    Nyhuis, P., Wiendahl, H-P. & Wagner, C., 2012, Montage in der industriellen Produktion. Lotter, B. & Wiendahl, H-P. (eds.). 2 ed. Berlin: Springer, p. 285-313 29 p.

    Research output: Contributions to collected editions/works › Contributions to collected editions/anthologies › Education

  45. Published

    Kontinuierliche Gestaltung skalierbarer Produktionsstufen

    Wagner, C., 2012, Garbsen: PZH Verlag. 153 p. (Berichte aus dem IFA; vol. 2012, no. 3)

    Research output: Books and anthologies › Monographs › Research

  46. Published

    Drahtloses und bildgebendes Multi-Sensorsystem integriert in eine Handgelenksorthese für ein nichtinvasives Langzeitmonitoring

    Schimmack, M., Georgiadis, A., Suhkhikh, R. & Siemsen, C. H., 01.01.2012, Sensoren und Messsysteme 2012: Vorträge der 16. GMA/ITG-Fachtagung vom 22. bis 23. Mai 2012 in Nürnberg ; Tagungsband. AMA Service, p. 603-609 7 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  47. Homogenization modeling of thin-layer-type microstructures

    Klusemann, B. & Svendsen, B., 15.06.2012, In: International Journal of Solids and Structures. 49, 13, p. 1828-1838 11 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  48. A novel radio-frequency plasma probe for monitoring systems in dielectric deposition processes

    Schulz, C., Styrnoll, T., Lapke, M., Oberrath, J., Storch, R., Awakowicz, P., Brinkmann, R. P., Musch, T., Mussenbrock, T. & Rolfes, I., 2012, Proceedings of the 2012 International Conference on Electromagnetics in Advanced Applications, ICEAA'12: ICEAA '12. IEEE - Institute of Electrical and Electronics Engineers Inc., Vol. 2. p. 728-731 4 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  49. The multipole resonance probe: Investigation of an active plasma resonance probe using 3D-electromagnetic field simulations

    Schulz, C., Rolfes, I., Styrnoll, T., Awakowicz, P., Lapke, M., Oberrath, J., Mussenbrock, T., Brinkmann, R. P., Storch, R. & Musch, T., 2012, 42nd European Microwave Conference (EuMC 2012): Proceedings. IEEE - Institute of Electrical and Electronics Engineers Inc., p. 566-569 4 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  50. Published

    A cascade controller structure using an internal PID controller for a hybrid piezo-hydraulic actuator in camless internal combustion engines

    Mercorelli, P. & Werner, N., 2013, 2013 9th Asian Control Conference, ASCC 2013. IEEE - Institute of Electrical and Electronics Engineers Inc., p. 1-6 6 p. 6606090. (2013 9th Asian Control Conference, ASCC 2013).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

Previous 1...3 4 5 6 7 8 9 10 ...34 Next