1. //
  2. Start
  3. //
  4. Publications
  5. //
  6. Browse
  7. //

Browse by research area

1 - 10 out of 1,895Page size: 10
  1. Published

    Three-dimensional mapping of residual stresses and crack propagation in refill friction stir spot welded aluminium samples via synchrotron X-ray diffraction and X-ray micro-computed tomography

    Bernardi, M., Canelo-Yubero, D., Chen, T., Suhuddin, U. F. H., Bergmann, L. & Klusemann, B., 01.2026, In: International Journal of Fatigue. 202, 11 p., 109223.

    Research output: Journal contributions › Journal articles › Research › peer-review

  2. Published

    Field-Based Assessment of Key Influence Factors for Throughput Time Prediction in Job Shop Manufacturing

    Reinhold, J., Rokoss, A. & Schmidt, M., 2026, Advances in Production Management Systems. Cyber-Physical-Human Production Systems: Human-AI Collaboration and Beyond - 44th IFIP WG 5.7 International Conference, APMS 2025, Proceedings. Mizuyama, H., Morinaga, E., Kaihara, T., Nonaka, T., von Cieminski, G. & Romero, D. (eds.). Springer Science and Business Media Deutschland, p. 201-215 15 p. (IFIP Advances in Information and Communication Technology; vol. 769 IFIPAICT).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  3. Published

    Trans pixelate substitution scheme for denoising computed tomography images towards high diagnosis accuracy

    Hu, F., Gu, H., Wu, F., Lhioui, C., Othmen, S., Alfahid, A., Yousef, A. & Mercorelli, P., 12.2025, In: Scientific Reports. 15, 1, 23 p., 11525.

    Research output: Journal contributions › Journal articles › Research › peer-review

  4. Published

    Precipitation distribution in mechanically alloyed Al-Cu-Li powders processed via friction consolidation

    Chan, C. Y. C., Suhuddin, U. F. H. R., Maawad, E., Mordridge, M. T. & Klusemann, B., 11.2025, In: Materials and Design. 259, 12 p., 114847.

    Research output: Journal contributions › Journal articles › Research › peer-review

  5. Published

    Failure prediction by using a recurrent neural network in incremental sheet forming with active medium

    Thiery, S., Zein El Abdine, M., Heger, J. & Ben Khalifa, N., 30.10.2025, In: International Journal of Material Forming. 18, 4, 15 p., 91.

    Research output: Journal contributions › Journal articles › Research › peer-review

  6. Published

    Improving mechanical properties of constrained friction processing Mg-Zn-Ca alloys by modifying texture using multiple pass processing

    Chen, T., Fu, B., Suhuddin, U. F. H. R., Shen, T., Li, G., Maawad, E., Shen, J., Santos, J. F. D., Bergmann, J. P. & Klusemann, B., 10.10.2025, In: Journal of Materials Science and Technology. 232, p. 209-226 18 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  7. Adaptive acquisition planning for visual inspection in remanufacturing using reinforcement learning

    Kaiser, J. P., Gäbele, J., Koch, D., Schmid, J., Stamer, F. & Lanza, G., 10.2025, In: Journal of Intelligent Manufacturing. 36, 7, p. 4867-4893 27 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  8. Published

    Additive friction stir deposition vs. friction surfacing: Comparison of friction stir-based approaches for groove repair of high strength aluminum alloys

    Kallien, Z., Rojas, V. A., Aspes, P., Swinney, A. N., Fleck, T. J., Jordon, J. B., Allison, P. G. & Klusemann, B., 10.2025, In: Materials and Design. 258, 14 p., 114511.

    Research output: Journal contributions › Journal articles › Research › peer-review

  9. Published

    From cost to capability: Technology Multiplier in EV manufacturing strategy

    Girke, R., Schäfer, L., Maier, T., Stamer, F., Yang, S., Chun, J. H. & Lanza, G., 10.2025, In: Journal of Manufacturing Systems. 82, p. 319-332 14 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  10. Published

    Analysis of piezoelectric harvester with multi-array configuration for ultra-low power sensor nodes

    Schott, L., Bouattour, G., Fromm, R., Strakosch, F., Kanoun, O. & Derbel, F., 27.09.2025, In: Results in Engineering. 27, 17 p., 106728.

    Research output: Journal contributions › Journal articles › Research › peer-review

Previous 1 2 3 4 5 6 7 8 ...190 Next

Recently viewed

Publications

  1. A Rigorous Climate Policy Is Necessary in Order to Give Incentives for Energy Suppliers to Develop Innovative and Environmentally Friendly Technologies
  2. Mathe darstellend vernetzen
  3. Carnivores’ contributions to people in Europe
  4. Erinnern Vergessen.
  5. Об организации и научно-методическом обеспечении практики студентов специальности «Социальная работа»
  6. Farewell to the White Space?
  7. Liebe
  8. Arts and Power
  9. Fluctuations of carabid populations inhabiting an ancient woodland (Coleoptera, Carabidae)
  10. Entwicklung und Zukunft der Sexualität und Liebe
  11. Heidegger and Merleau-Ponty: Being-in-the-world with others?
  12. Reconceptualising European equality law
  13. The influence of laser shock peening on fatigue properties of AA2024-T3 alloy with a fastener hole
  14. Zeitlichkeit und Kognition im Hochfrequenzhandel
  15. Cybervictimization, self-esteem, and social relationships among German secondary school students
  16. A comparison of feasible methods for microalgal biomass determinations during tertiary wastewater treatment
  17. Zur Konzeption des Subjekts im Globalen Lernen
  18. Lost in Media
  19. Investigations on microstructures, mechanical and corrosion properties of Mg-Gd-Zn alloys
  20. The influence of the radial internal clearance on the dynamic response of self-aligning ball bearings
  21. Anleihekommunikation in der Unternehmenspraxis
  22. Gerd Hurm: Rewriting the Vernacular Mark Twain
  23. Das Treasury lenkt mit
  24. Frömmigkeit der Theologie, zur Logik der offenen Theodizeefrage
  25. T-Shirts auf dem Campus
  26. Die Aufgabe der Fünfziger