1. //
  2. Start
  3. //
  4. Publications
  5. //
  6. Browse
  7. //

Browse by research area

1441 - 1450 out of 1,733Page size: 10

  1. An observer for sensorless variable valve control in camless internal combustion engines

    Mercorelli, P., 2010, 6th IFAC Symposium Advances in Automotive Control, AAC 2010. Trächtler, A. & Abel, D. (eds.). International Federation of Automatic Control, p. 306-311 6 p. (IFAC Proceedings Volumes (IFAC-PapersOnline); vol. 43, no. 7).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  2. Application of crystal plasticity to modeling the deformation behavior of sheet metal mesocrystals

    Klusemann, B., Svendsen, B. & Vehoff, H., 2010, Fifth International Conference Multiscale Materials Modeling - MMM 2010: Proceedings : October 4-8, 2010, Freiburg, Germany. Fraunhofer Verlag, Vol. 5. p. 447 – 450 4 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  3. Approaching bolt load retention behaviour of AS41 through compliance and creep deformation

    Anopuo, O., Huang, Y., Hort, N., Dieringa, H. & Kainer, K. U., 2010, Magnesium Technology 2010 - Held During TMS 2010 Annual Meeting and Exhibition. Agnew, S. R., Neelameggham, N. R., Nyberg, E. A. & Sillekens, W. H. (eds.). John Wiley & Sons Inc., p. 215-220 6 p. (Magnesium Technology).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  4. Arc spraying of WCFeCSiMn cored wires. Part 2: E-Module measurement and simulation

    Nebel, J., Klusemann, B., Tillmann, W. & Svendsen, B., 2010, Thermal Spray 2010: Global Solutions for Future Applications: Proceedings of the International Thermal Spray Conference. Marple, B. R., Agarwal, A., Hyland, M. M., Li, Y-C., Lima, R. S. & Montavon, G. (eds.). New York: Springer, p. 782–789 18 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  5. Published

    Bildung für nachhaltige Entwicklung: Projektmentoring als innovatives Lehr-Lernkonzept in den Ingenieurwissenschaften

    Block, B-M., 2010, IngenieurBildung für nachhaltige Eintwicklung. Kammasch, G., Wieneke-Toutaoui, A. & Schwenk, B. (eds.). Beuth Verlag, p. 45-50 7 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  6. Composite extrusion and threading of continuously reinforced aluminium profiles

    Engbert, T., Biermann, D., Zabel, A., Pietzka, D., Tekkaya, A. E. & Ben Khalifa, N., 2010, In: International Aluminium Journal. 86, 4, p. 36-41 6 p.

    Research output: Journal contributions › Journal articles › Research

  7. Development of recyclable Mg-based alloys: Az91d and Azc1231 phase information derived from heating/cooling curve analysis

    Gesing, A. J., Reade, N. D., Sokolowski, J. H., Blawert, C., Fechner, D. & Hort, N., 2010, Magnesium Technology 2010 - Held During TMS 2010 Annual Meeting and Exhibition. Agnew, S. R., Neelameggham, N. R., Nyberg, E. A. & Sillekens, W. H. (eds.). John Wiley & Sons Inc., p. 97-105 9 p. (Magnesium Technology).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  8. Effect of minor additions of Al and Si on the mechanical properties of cast Mg-3Sn-2Ca alloys in low temperature range

    Rao, K. P., Suresh, K., Hort, N. & Kainer, K. U., 2010, PRICM7. Nie, J-F. & Morton, A. (eds.). Trans Tech Publications Ltd, p. 635-638 4 p. (Materials Science Forum; vol. 654-656).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  9. Extrusion benchmark 2009 experimental analysis of deflection in extrusion dies

    Pietzka, D., Ben Khalifa, N., Lorenzo, D., Tomesani, L. & Tekkaya, A. E., 2010, Advances on hot extrusion and simulation of light alloys: selected, peer reviewed papers from the International Conference on Extrusion and Benchmark (ICEB). Tekkaya, A. E. & Ben Khalifa, N. (eds.). Trans Tech Publications, Vol. 424. p. 19-26 8 p. (Key Engineering Materials; vol. 424).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  10. Friction model selection in FEM simulations of aluminium extrusion

    Donati, L., Tomesani, L., Schikorra, M., Ben Khalifa, N. & Tekkaya, A. E., 2010, In: International Journal of Surface Science and Engineering. 4, 1, p. 27-41 15 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

Previous 1...141 142 143 144 145 146 147 148 ...174 Next