1. //
  2. Start
  3. //
  4. Publications
  5. //
  6. Browse
  7. //

Browse by research area

1271 - 1280 out of 1,858Page size: 10
  1. Published

    Optical part measuring inside a milling machine

    Meier, N. & Georgiadis, A., 2014, Measurement Technology and Intelligent Instruments XI. Schmitt, R. & Bosse, H. (eds.). Trans Tech Publ., p. 440-445 6 p. (Key Engineering Materials; vol. 613).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  2. Published

    Parameters identification in a permanent magnet three-phase synchronous motor of a city-bus for an intelligent drive assistant

    Mercorelli, P., 2014, In: International Journal of Modelling, Identification and Control. 21, 4, p. 352-361 10 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  3. Published

    Programmierung einer DELTA-Roboterzelle nach PackML Standard

    Odensass, P., 2014, Tagungsband AALE 2014: Das Forum für Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft, 11. Fachkonferenz, Regensburg. Regensburg: DIV Deutscher Industrieverlag GmbH, p. 221-230 10 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Transfer

  4. Residual stresses near the hot sprues of as-cast Mg-Zn alloys investigated by STRESS-SPEC neutron diffractometer

    Gan, W. M., Huang, Y. D., Wang, Z., Hort, N. & Hofmann, M., 2014, International Conference on Residual Stresses 9 (ICRS 9). Kurz, S. J. B., Mittemeijer, E. J. & Scholtes, B. (eds.). Trans Tech Publications Ltd, p. 428-432 5 p. (Materials Science Forum; vol. 768-769).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  5. Simulation of composite hot extrusion with high reinforcing Volumes

    Schwane, M., Citrea, T., Dahnke, C., Haase, M., Ben Khalifa, N. & Tekkaya, A. E., 2014, In: Procedia Engineering. 81, p. 1265-1270 6 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  6. Standort- und Netzwerkplanung in Metropolregionen: Aktueller Forschungsbedarf bei Entscheidungsmodellen

    Richter, L., Lübkemann, J., Schmidt, M. & Nyhuis, P., 2014, In: wt Werkstattstechnik online. 104, 4, p. 202-205 4 p.

    Research output: Journal contributions › Journal articles › Research

  7. Published

    Steady State Detection for the Context Aware Evaluation of Vital Signs

    Busch, B.-H. & Welge, R., 2014, Wohnen – Pflege – Teilhabe: Besser leben durch Technik - 7. AAL-Kongress mit Ausstellung 21.-22. Januar 2014 in Berlin, Tagungsbeiträge. VDE Verlag, 8 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  8. Strangpressen von Profilen mit variabler Wandstärke

    Selvaggio, A., Haase, M., Ben Khalifa, N. & Tekkaya, A. E., 2014, In: International Aluminium Journal. 90, 11, p. 49-51 3 p.

    Research output: Journal contributions › Journal articles › Research

  9. Published

    Using Euler Discrete Approximation to Control an Aggregate Actuator in Camless Engines

    Mercorelli, P. & Werner, N., 2014, In: International Journal of Mathematical Models and Methods in Applied Sciences . 8, 1, p. 273-280 8 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  10. Thermodynamic assessment and experimental study of Mg-Gd alloys

    Hampl, M., Blawert, C., Silva Campos, M. R., Hort, N., Peng, Q., Kainer, K. U. & Schmid-Fetzer, R., 25.12.2013, In: Journal of Alloys and Compounds. 581, p. 166-177 12 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

Previous 1...124 125 126 127 128 129 130 131 ...186 Next

Recently viewed