1. //
  2. Start
  3. //
  4. Publications
  5. //
  6. Browse
  7. //

Browse by research area

1231 - 1240 out of 1,666Page size: 10
Sort by: Title
  1. Published

    Optimization of transport flow on two paths with respect to the passengers time costs

    Mercorelli, P., 29.10.2021, In: International Journal of Circuits, Systems and Signal Processing. 15, p. 1602-1606 5 p., 172.

    Research output: Journal contributions › Journal articles › Research › peer-review

  2. Optimum parameters and rate-controlling mechanisms for hot working of extruded Mg-3Sn-1Ca alloy

    Prasad, Y. V. R. K., Rao, K. P., Hort, N. & Kainer, K. U., 25.02.2009, In: Materials Science and Engineering A. 502, 1-2, p. 25-31 7 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  3. Published

    Orthopädische Biomechanik: Einführung in die Endoprothetik der Gelenke der unteren Extremitäten

    Dittrich, H., Schimmack, M. & Siemsen, C-H., 07.2019, 1 ed. Berlin, Heidelberg: Springer Vieweg. 186 p.

    Research output: Books and anthologies › Compendium/lecture notes › Education

  4. Published

    Outperformed by a Computer? - Comparing Human Decisions to Reinforcement Learning Agents, Assigning Lot Sizes in a Learning Factory: 11th Conference on Learning Factories, CLF2021

    Voß, T., Rokoss, A., Maier, J. T., Schmidt, M. & Heger, J., 06.2021, Rochester: Elsevier Inc., 6 p. (SSRN).

    Research output: Working paper › Working papers

  5. Published

    Parameter Investigation for the In-Situ Hybridization Process by Deep Drawing of Dry Fiber-Metal-Laminates

    Kruse, M., Lehmann, J. & Ben Khalifa, N., 01.01.2023, Production at the Leading Edge of Technology: Proceedings of the 12th Congress of the German Academic Association for Production Technology (WGP), University of Stuttgart, October 2022. Liewald, M., Verl, A., Bauernhansl, T. & Möhring, H-C. (eds.). Cham: Springer, p. 122-130 9 p. (Lecture Notes in Production Engineering; vol. Part F1163).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  6. Published

    Parameterized Synthetic Image Data Set for Fisheye Lens

    Zhen, C. & Georgiadis, A., 02.07.2018, Proceedings - 2018 5th International Conference on Information Science and Control Engineering, ICISCE 2018. Cheng, Y., Li, S. & Dai, Y. (eds.). IEEE - Institute of Electrical and Electronics Engineers Inc., p. 370-374 5 p. 8612582

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  7. Published

    Parameters Estimation of a Lotka-Volterra Model in an Application for Market Graphics Processing Units

    Normatov, D. & Mercorelli, P., 26.09.2022, Proceedings of the 17th Conference on Computer Science and Intelligence Systems. Ganzha, M., Maciaszek, L., Paprzycki, M. & Slezak, D. (eds.). Warsaw: Polish Information Processing Society, p. 935-938 4 p. (Annals of Computer Science and Information System; vol. 30).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  8. Published

    Parameters identification in a permanent magnet three-phase synchronous motor for velocity planning to optimize traction losses in a City-Bus

    Mercorelli, P., 2013, 2013 Proceedings of International Conference on Modelling, Identification and Control, ICMIC 2013. IEEE - Institute of Electrical and Electronics Engineers Inc., p. 193-198 6 p. 6642173. (2013 Proceedings of International Conference on Modelling, Identification and Control, ICMIC 2013).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  9. Published

    Parameters identification in a permanent magnet three-phase synchronous motor of a city-bus for an intelligent drive assistant

    Mercorelli, P., 2014, In: International Journal of Modelling, Identification and Control. 21, 4, p. 352-361 10 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  10. Published

    Parametric finite element model and mechanical characterisation of electrospun materials for biomedical applications

    Polak-Kraśna, K., Mazgajczyk, E., Heikkilä, P. & Georgiadis, A., 07.01.2021, In: Materials. 14, 2, p. 1-15 15 p., 278.

    Research output: Journal contributions › Journal articles › Research › peer-review

Previous 1...120 121 122 123 124 125 126 127 ...167 Next