1. //
  2. Start
  3. //
  4. Publications
  5. //
  6. Browse
  7. //

Browse by research area

1101 - 1120 out of 1,675Page size: 20

  1. Application of non-convex rate dependent gradient plasticity to the modeling and simulation of inelastic microstructure development and inhomogeneous material behavior

    Klusemann, B., Yalçinkaya, T., Geers, M. G. D. & Svendsen, B., 12.2013, In: Computational Materials Science. 80, p. 51-60 10 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  2. Microstructure and mechanical properties of as-cast Mg-Sn-Ca alloys and effect of alloying elements

    Suresh, K., Rao, K. P., Prasad, Y. V. R. K., Hort, N. & Kainer, K. U., 12.2013, In: Transactions of Nonferrous Metals Society of China (English Edition). 23, 12, p. 3604-3610 7 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  3. Maschinen- und werkzeugseitige Herausforderungen bei der Blechmassivumformung von komplexen Bauteilen

    Salfeld, V., Matthias, T., Krimm, R., Behrens, B-A., Sieczkarek, P., Ben Khalifa, N., Tekkaya, A. E., Hetzner, H., Tremmel, S. & Wartzack, S., 13.11.2013, Tagungsband zum 2. Erlanger Workshop Blechmassivumformung 2013: 2. Workshop Blechmassivumformung. Merklein, M., Behrens, B. A. & Tekkaya, A. E. (eds.). Meisenbach GmbH Verlag, p. 13-35 23 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  4. Comparison of different in vitro tests for biocompatibility screening of Mg alloys

    Scheideler, L., Füger, C., Schille, C., Rupp, F., Wendel, H. P., Hort, N., Reichel, H. P. & Geis-Gerstorfer, J., 11.2013, In: Acta Biomaterialia. 9, 10, p. 8740-8745 6 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  5. Element distribution in the corrosion layer and cytotoxicity of alloy Mg-10Dy during in vitro biodegradation

    Yang, L., Hort, N., Laipple, D., Höche, D., Huang, Y., Kainer, K. U., Willumeit, R. & Feyerabend, F., 11.2013, In: Acta Biomaterialia. 9, 10, p. 8475-8487 13 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  6. Fast escape of hydrogen from gas cavities around corroding magnesium implants

    Kuhlmann, J., Bartsch, I., Willbold, E., Schuchardt, S., Holz, O., Hort, N., Höche, D., Heineman, W. R. & Witte, F., 11.2013, In: Acta Biomaterialia. 9, 10, p. 8714-8721 8 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  7. Microstructure, mechanical and corrosion properties of Mg-Dy-Gd-Zr alloys for medical applications

    Yang, L., Huang, Y., Feyerabend, F., Willumeit, R., Mendis, C., Kainer, K. U. & Hort, N., 11.2013, In: Acta Biomaterialia. 9, 10, p. 8499-8508 10 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  8. Modeling and simulation of deformation behavior, orientation gradient development and heterogeneous hardening in thin sheets with coarse texture

    Klusemann, B., Svendsen, B. & Vehoff, H., 11.2013, In: International Journal of Plasticity. 50, p. 109-126 18 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  9. Published

    Combining Model Predictive and Adaptive Control for an Atomic Force Microscope Piezo-Scanner-Cantilever System

    Fuhrhop, C., Mercorelli, P. & Georgiadis, A., 10.2013, 2013 IEEE International Symposium on Sensorless Control for Electrical Drives and Predictive Control of Electrical Drives and Power Electronics (SLED/PRECEDE) : 2013 IEEE International Symposium. IEEE - Institute of Electrical and Electronics Engineers Inc., 6 p. 6684499. (SLED/PRECEDE 2013 - 2013 IEEE International Symposium on Sensorless Control for Electrical Drives and Predictive Control of Electrical Drives and Power Electronics).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  10. Evolutionary generation of dispatching rule sets for complex dynamic scheduling problems

    Pickardt, C. W., Hildebrandt, T., Branke, J., Heger, J. & Scholz-Reiter, B., 09.2013, In: International Journal of Production Economics. 145, 1, p. 67-77 11 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  11. Modeling of a thermomechanical process chain for sheet steels

    Barthel, C., Klusemann, B., Denzer, R. & Svendsen, B., 09.2013, In: International Journal of Mechanical Sciences. 74, p. 46-54 9 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  12. Plastic deformation induced microstructure evolution through gradient enhanced crystal plasticity based on a non-convex Helmholtz energy

    Klusemann, B. & Yalçinkaya, T., 09.2013, In: International Journal of Plasticity. 48, p. 168-188 21 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  13. Development of a magnesium secondary alloy system for mixed magnesium post-consumer scrap

    Fechner, D., Blawert, C., Hort, N., Dieringa, H. & Kainer, K. U., 01.08.2013, In: Materials Science and Engineering A. 576, p. 222-230 9 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  14. An analytical approach to evaluating monotonic functions of fuzzy numbers

    Seibel, A. & Schlattmann, J., 08.2013, 8th Conference of the European Society for Fuzzy Logic and Technology, EUSFLAT 2013 - Advances in Intelligent Systems Research. Atlantis Press, p. 289-293 5 p. (8th Conference of the European Society for Fuzzy Logic and Technology, EUSFLAT 2013 - Advances in Intelligent Systems Research; vol. 32).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  15. Controlling heat balance in hot aluminum extrusion by additive manufactured extrusion dies with conformal cooling channels

    Hölker, R., Jäger, A., Ben Khalifa, N. & Tekkaya, A. E., 08.2013, In: International Journal of Precision Engineering and Manufacturing. 14, 8, p. 1487-1493 7 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  16. High temperature deformation and microstructural features of TXA321 magnesium alloy: Correlations with processing map

    Dharmendra, C., Rao, K. P., Prasad, Y. V. R. K., Hort, N. & Kainer, K. U., 08.2013, In: Advanced Engineering Materials. 15, 8, p. 761-766 6 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  17. Hot workability analysis with processing map and texture characteristics of as-cast TX32 magnesium alloy

    Dharmendra, C., Rao, K. P., Prasad, Y. V. R. K., Hort, N. & Kainer, K. U., 08.2013, In: Journal of Materials Science. 48, 15, p. 5236-5246 11 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  18. Published

    Setting controller parameters through a minimum strategy with a weighted least squares method

    Mercorelli, P., 19.07.2013, In: International Journal of Pure and Applied Mathematics. 86, 2, p. 457-463 7 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  19. Published

    Modeling approach of thermal decomposition of salt-hydrates for heat storage systems

    Fopah Lele, A., Kuznik, F., Rammelberg, H., Schmidt, T. & Ruck, W., 14.07.2013, ASME 2013 Heat Transfer Summer Conference collocated with the ASME 2013 7th International Conference on Energy Sustainability and the ASME 2013 11th International Conference on Fuel Cell Science, Engineering and Technology: Heat Transfer in Energy Systems; Thermophysical Properties; Theory and Fundamental Research in Heat Transfer. ASME. (ed.). The American Society of Mechanical Engineers (ASME), Vol. 1. p. Paper No. HT2013-17022, pp. V001T01A010; 10 pages 10 p. V001T01A010. (ASME 2013 Heat Transfer Summer Conference collocated with the ASME 2013 7th International Conference on Energy Sustainability and the ASME 2013 11th International Conference on Fuel Cell Science, Engineering and Technology; vol. 1).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  20. Effect of die design on the welding quality during solid state recycling of AA6060 chips by hot extrusion

    Güley, V., Güzel, A., Jäger, A., Ben Khalifa, N., Tekkaya, A. E. & Misiolek, W. Z., 01.07.2013, In: Materials Science & Engineering A. 574, p. 163-175 13 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

Previous 1...52 53 54 55 56 57 58 59 ...84 Next