1. //
  2. Start
  3. //
  4. Publications
  5. //
  6. Browse
  7. //

Browse by research area

1141 - 1150 out of 1,733Page size: 10

  1. Magnesium alloy containing silver for degradable biomedical implants

    Lukáč, F., Vlček, M., Stulíková, I., Smola, B., Kudrnová, H., Vlach, M., Kekule, T., Szakács, G., Hort, N. & Kainer, K. U., 2014, METAL 2014 - 23rd International Conference on Metallurgy and Materials, Conference Proceedings. TANGER Ltd., p. 1086-1091 6 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  2. Mechanical properties and microstructures of nano SiC reinforced ZE10 composites prepared with ultrasonic vibration

    Song, J. F., Dieringa, H., Huang, Y. D., Gan, W. M., Kainer, K. U. & Hort, N., 2014, AMI Light Metals Conference 2014. Curle, U. A. & Möller, H. (eds.). Trans Tech Publications Ltd, p. 169-176 8 p. (Advanced Materials Research; vol. 1019).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  3. Microstructure and compression creep strength of the newly developed magnesium alloy DieMag422

    Dieringa, H., Hort, N. & Kainer, K. U., 2014, AMI Light Metals Conference 2014. Curle, U. A. & Möller, H. (eds.). Trans Tech Publications Ltd, p. 177-183 7 p. (Advanced Materials Research; vol. 1019).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  4. Modeling of lateness distributions depending on the sequencing method with respect to productivity effects

    Bertsch, S., Schmidt, M. & Nyhuis, P., 2014, In: CIRP Annals - Manufacturing Technology. 63, 1, p. 429-432 4 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  5. Non-local modeling of size effects in amorphous metals

    Klusemann, B. & Xiao, T., 2014, PAMM Proceedings in Aplied Mathematics and Mechanics: 85th Annual Meeting of the International Association of Applied Mathematics and Mechanics (GAMM). Steinmann, P. & Leugering, G. (eds.). 1 ed. Wiley-Blackwell Publishing, Inc., Vol. 14. p. 527-528 2 p. (Proceedings in Applied Mathematics and Mechanics; vol. 14, no. 1 Special issue).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  6. Published

    Optical part measuring inside a milling machine

    Meier, N. & Georgiadis, A., 2014, Measurement Technology and Intelligent Instruments XI. Schmitt, R. & Bosse, H. (eds.). Trans Tech Publ., p. 440-445 6 p. (Key Engineering Materials; vol. 613).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  7. Published

    Parameters identification in a permanent magnet three-phase synchronous motor of a city-bus for an intelligent drive assistant

    Mercorelli, P., 2014, In: International Journal of Modelling, Identification and Control. 21, 4, p. 352-361 10 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  8. Published

    Programmierung einer DELTA-Roboterzelle nach PackML Standard

    Odensass, P., 2014, Tagungsband AALE 2014: Das Forum für Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft, 11. Fachkonferenz, Regensburg. Regensburg: DIV Deutscher Industrieverlag GmbH, p. 221-230 10 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Transfer

  9. Residual stresses near the hot sprues of as-cast Mg-Zn alloys investigated by STRESS-SPEC neutron diffractometer

    Gan, W. M., Huang, Y. D., Wang, Z., Hort, N. & Hofmann, M., 2014, International Conference on Residual Stresses 9 (ICRS 9). Kurz, S. J. B., Mittemeijer, E. J. & Scholtes, B. (eds.). Trans Tech Publications Ltd, p. 428-432 5 p. (Materials Science Forum; vol. 768-769).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  10. Simulation of composite hot extrusion with high reinforcing Volumes

    Schwane, M., Citrea, T., Dahnke, C., Haase, M., Ben Khalifa, N. & Tekkaya, A. E., 2014, In: Procedia Engineering. 81, p. 1265-1270 6 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

Previous 1...111 112 113 114 115 116 117 118 ...174 Next