1. //
  2. Start
  3. //
  4. Publications
  5. //
  6. Browse
  7. //

Browse by research area

961 - 970 out of 1,675Page size: 10

  1. A genetic algorithm for a self-learning parameterization of an aerodynamic part feeding system for high-speed assembly

    Busch, J., Quirico, M., Richter, L., Schmidt, M., Raatz, A. & Nyhuis, P., 2015, In: CIRP Annals - Manufacturing Technology. 64, 1, p. 5-8 4 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  2. Published

    A Hybrid Actuator and its Control Using a Cascade Sliding Mode Technique

    Mercorelli, P., 2015, Sliding Mode Control (SMC): Theory, Perspectives and Industrial Applications. Ellis, D. T. (ed.). New York: Nova Science Publishers, Inc., p. 167-184 18 p. 9. (Mechanical Engineering Theory and Applications).

    Research output: Contributions to collected editions/works › Contributions to collected editions/anthologies › Research › peer-review

  3. Published

    A model predictive control for an aggregate actuator with a self-tuning initial condition procedure in combustion engines

    Mercorelli, P., Werner, N. & Haus, B., 2015, Model Predictive Control: Theory, Practices and Future Challenges. Wade, C. (ed.). New York: Nova Science Publishers, Inc., p. 41-59 19 p. 2. (Mechanical Engineering Theory and Applications).

    Research output: Contributions to collected editions/works › Contributions to collected editions/anthologies › Research › peer-review

  4. Published

    An indirectly controlled high-speed servo valve for IC engines using piezo actuators

    Behre, L., Becker, U., Van Niekerk, T., Harndorf, H., Mercorelli, P. & Werner, N., 2015, In: R & D Journal. 31, p. 35-45 11 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  5. Approaches for the Simulation of Composite Extrusion - Possibilities and Limits

    Schwane, M., Kloppenborg, T., Haase, M., Ben Khalifa, N. & Tekkaya, A. E., 2015, In: Materials Today: Proceedings . 2, 10 (Part A), p. 4771-4777 7 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  6. Automatic generation of periodic representative volume elements for matrix-inclusion composites and their efficiency in multiscaling

    Schneider, K., Klusemann, B. & Bargmann, S., 2015, Proceedings of the NSCM28. Berezovski, A., Tamm, K. & Peets, T. (eds.). Tallinn University of Technology, p. 153-156 4 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research

  7. Basic investigations in incremental profile forming

    Grzancic, G., Becker, C., Ben Khalifa, N. & Tekkaya, A. E., 2015, Proceedings of theASME 10th International Manufacturing Science and Engineering Conference - 2015: Processing. The American Society of Mechanical Engineers (ASME), Vol. 1. p. V001T02A095

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  8. Published

    Coplanar micro-strips/electrospun sensor system to measure the electronics properties of the polyethylene oxide (PEO) electrospun

    Fuhrhop, C. & Georgiadis, A., 2015, 2015 IEEE International Symposium on Medical Measurements and Applications, MeMeA 2015 - Proceedings. IEEE - Institute of Electrical and Electronics Engineers Inc., p. 512-516 5 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  9. Correlation between mechanical behaviour and microstructure in the Mg-Ca-Si-Sr system for degradable biomaterials based on thermodynamic calculations

    Gil-Santos, A., Szakacs, G., Moelans, N., Hort, N. & Van Der Biest, O., 2015, Magnesium Technology 2015 - Held During TMS 2015 144th Annual Meeting and Exhibition. Manuel, M. V., Singh, A., Alderman, M., Alderman, M. & Neelameggham, N. R. (eds.). The Minerals, Metals & Materials Society, p. 431-436 6 p. (Magnesium Technology; vol. 01/2015).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  10. Deformation-induced dynamic precipitation during creep in magnesium-tin alloys

    Huang, Y., Dieringa, H., Kainer, K. U. & Hort, N., 2015, In: Key Engineering Materials. 627, p. 365-368 4 p.

    Research output: Journal contributions › Conference article in journal › Research › peer-review

Previous 1...93 94 95 96 97 98 99 100 ...168 Next