Browse by research area

  1. Published

    Comparison on Hot Tearing Behavior of Binary Mg–Al, Mg–Y, Mg–Gd, Mg–Zn, and Mg–Ca Alloys

    Song, J., Zhao, H., Liao, J., Jiang, B., Zhang, A., Huang, Y., Kainer, K. U., Hort, N. & Pan, F., 08.2022, In: Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. 53, 8, p. 2986-3001 16 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  2. Published

    Comparison of Friction Extrusion Processing from Bulk and Chips of Aluminum-Copper Alloys

    Rath, L., Suhuddin, U. F. H. & Klusemann, B., 22.07.2022, Achievements and Trends in Material Forming: Peer-reviewed extended papers selected from the 25 th International Conference on Material Forming (ESAFORM 2022). Vincze, G. & Barlat, F. (eds.). Baech: Trans Tech Publications Ltd, p. 471-480 10 p. (Key Engineering Materials; vol. 926).

    Research output: Contributions to collected editions/worksArticle in conference proceedingsResearchpeer-review

  3. Published

    Effect of Temperature and Strain Rate on Formability of Titanium Alloy KS1.2ASN

    Sikhamov, R., Ventzke, V., Dorn, F., Klusemann, B., Khalifa, N. B. & Kashaev, N., 22.07.2022, Achievements and Trends in Material Forming: Peer-reviewed extended papers selected from the 25 th International Conference on Material Forming (ESAFORM 2022). Vincze, G. & Barlat, F. (eds.). Baech: Trans Tech Publications Ltd, p. 939-946 8 p. (Key Engineering Materials; vol. 926).

    Research output: Contributions to collected editions/worksArticle in conference proceedingsResearchpeer-review

  4. Published

    Experimental Investigation of Efficiency and Deposit Process Temperature During Multi-Layer Friction Surfacing

    Kallien, Z., Roos, A. & Klusemann, B., 22.07.2022, Achievements and Trends in Material Forming: Peer-reviewed extended papers selected from the 25 th International Conference on Material Forming (ESAFORM 2022). Vincze, G. & Barlat, F. (eds.). Baech: Trans Tech Publications Ltd, p. 187-193 7 p. (Key Engineering Materials; vol. 926).

    Research output: Contributions to collected editions/worksArticle in conference proceedingsResearchpeer-review

  5. Published

    Numerical Investigation of Influence of Spot Geometry in Laser Peen Forming of Thin-Walled Ti-6Al-4V Specimens

    Pöltl, D., Keller, S., Chupakhin, S., Sala, S. T., Kashaev, N. & Klusemann, B., 22.07.2022, Achievements and Trends in Material Forming: Peer-reviewed extended papers selected from the 25 th International Conference on Material Forming (ESAFORM 2022). Vincze, G. & Barlat, F. (eds.). Baech: Trans Tech Publications Ltd, p. 2293-2302 10 p. (Key Engineering Materials; vol. 926).

    Research output: Contributions to collected editions/worksArticle in conference proceedingsResearchpeer-review

  6. Published

    Towards 3D Process Simulation for In Situ Hybridization of Fiber-Metal-Laminates (FML)

    Poppe, C. T., Werner, H. O., Kruse, M., Chen, H., Ben Khalifa, N., Henning, F. & Kärger, L., 22.07.2022, In: Key Engineering Materials. 926, p. 1399-1412 14 p.

    Research output: Journal contributionsConference article in journalResearchpeer-review

  7. Published

    Anatomy of Chua's System - Nonlinear Dynamic Electronics for Chaos in the Lab

    Schimmack, M. & Mercorelli, P., 01.07.2022, In: IFAC-PapersOnLine. 55, 17, p. 302-307 6 p.

    Research output: Journal contributionsConference article in journalResearch

  8. Published

    A Theoretical Dynamical Noninteracting Model for General Manipulation Systems Using Axiomatic Geometric Structures

    Mercorelli, P., 01.07.2022, In: Axioms. 11, 7, 24 p., 309.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  9. Published

    Characterization of the deformation state of magnesium by electrical resistance

    Meyer, S., Wiese, B., Hort, N. & Willumeit-Römer, R., 01.07.2022, In: Scripta Materialia. 215, 4 p., 114712.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  10. Published

    Effect of laser peen forming process parameters on bending and surface quality of Ti-6Al-4V sheets

    Sala, S. T., Keller, S., Chupakhin, S., Pöltl, D., Klusemann, B. & Kashaev, N., 01.07.2022, In: Journal of Materials Processing Technology. 305, 16 p., 117578.

    Research output: Journal contributionsJournal articlesResearchpeer-review