1. //
  2. Start
  3. //
  4. Publications
  5. //
  6. Browse
  7. //

Browse by research area

121 - 130 out of 1,653Page size: 10

  1. Microstructure and mechanical properties of Mg-3Sn-1Ca reinforced with AlN nano-particles

    Wang, S., Huang, Y., Yang, L., Zeng, Y., Hu, Y., Zhang, X., Sun, Q., Shi, S., Meng, G. & Hort, N., 01.01.2023, In: Journal of Magnesium and Alloys. 11, 1, p. 259-269 11 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  2. Published

    Parameter Investigation for the In-Situ Hybridization Process by Deep Drawing of Dry Fiber-Metal-Laminates

    Kruse, M., Lehmann, J. & Ben Khalifa, N., 01.01.2023, Production at the Leading Edge of Technology: Proceedings of the 12th Congress of the German Academic Association for Production Technology (WGP), University of Stuttgart, October 2022. Liewald, M., Verl, A., Bauernhansl, T. & Möhring, H-C. (eds.). Cham: Springer, p. 122-130 9 p. (Lecture Notes in Production Engineering; vol. Part F1163).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  3. Published

    Simulationsbasierte Untersuchung von Energieflexibilität bei der Optimierung in der Hinterlandentwässerung

    Hempel, M. C. & Heger, J., 01.01.2023, ASIM Workshop 2023: STS/GMMS/EDU : Proceedings Langbeiträge : ASIM Fachgruppenworkshop 2023, STS Simulation Technischer Systeme, GMMS Grundlagen und Methoden in Modellbildung und Simulation, EDU Simulation und Edukation, 6.3.-7.3.2023, Universität Magdeburg. Krull, C., Commerell, W., Durak, U., Körner, A. & Pawletta, T. (eds.). Wien: ARGESIM Verlag , p. 143-149 7 p. (ASIM Mitteilung ; vol. 185)(ARGESIM Report; vol. 21).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  4. Published

    Effect of Welding Speed on Friction Stir Welds of PM2000 Alloy

    Wang, J., Fu, B., Bergmann, L., Liu, F. & Klusemann, B., 01.2023, In: Journal of Materials Engineering and Performance. 32, 2, p. 577-586 10 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  5. Additive Manufacturing of Soft Robots

    Weigand, F. & Seibel, A., 2023, Innovative Product Development by Additive Manufacturing 2021. Lachmayer, R., Bode, B. & Kaierle, S. (eds.). Cham: Springer International Publishing AG, p. 101-112 12 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  6. Published

    A Theory-Based Teaching Concept To Embed Sustainability In The Engineering Curriculum

    Block, B-M. & Guerne, M. G., 2023, Book of Proceedings for the 51st Annual Conference of the European Society for Engineering Education: Technological University Dublin 10th -14th September, 2023; Engineering Education for Sustainability. Reilly, G., Murphy, M., Nagy, B. V. & Jarvinen, H-M. (eds.). Brüssel: European Society for Engineering Education (SEFI), p. 1672-1680 9 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  7. Aufbau und Organisation von Entwicklungsprojekten

    Schlattmann, J. & Seibel, A., 2023, (Accepted/In press) 2. Aufl. ed. Berlin, Heidelberg: Springer. (Springer Reference Technik)

    Research output: Books and anthologies › Book

  8. Case study: The development of a multi-material heat sink by Additive Manufacturing using Aerosint technology

    Li, X. & Seibel, A., 2023, In: Metal Additive Manufacturing . 9, 1, p. 183-188 6 p.

    Research output: Journal contributions › Journal articles › Research

  9. Published

    Control of a Three-Axis Robot with Super Twisting Sliding Mode Control

    Rehbein, J. P., Haus, B. & Mercorelli, P., 2023, 27th International Conference on System Theory, Control and Computing, ICSTCC 2023 - Proceedings. Precup, R-E. (ed.). Institute of Electrical and Electronics Engineers Inc., p. 76-81 6 p. (International Conference on System Theory, Control and Computing, ICSTCC 2023 - Proceedings).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  10. Published

    Datenbasierte Bestimmung der Auftragsabwicklungsstrategie

    Maier, J. T., 2023, Göttingen: Sierke Verlag. 130 p. (Schriftenreihe Produktionstechnik und -systeme; vol. 21)

    Research output: Books and anthologies › Monographs › Research

Previous 1...9 10 11 12 13 14 15 16 ...166 Next