1. //
  2. Start
  3. //
  4. Publications
  5. //
  6. Browse
  7. //

Browse by research area

1431 - 1440 out of 1,666Page size: 10

  1. Aluminium-rich coring structures in Mg-Al alloys with carbon inoculation

    Huang, Y., Zheng, X., Okechukwu, A., Kim, G. S., Kainer, K. U. & Hort, N., 2010, PRICM7. Nie, J-F. & Morton, A. (eds.). Trans Tech Publications Ltd, p. 675-678 4 p. (Materials Science Forum; vol. 654-656).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  2. Simulation of stresses during casting of binary magnesium-aluminum alloys

    Pokorny, M. G., Monroe, C. A., Beckermann, C., Zhen, Z. & Hort, N., 12.2010, In: Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. 41, 12, p. 3196-3207 12 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  3. XPS studies of magnesium surfaces after exposure to Dulbecco's modified eagle medium, Hank's buffered salt solution, and simulated body fluid

    Tie, D., Feyerabend, F., Hort, N., Willumeit, R. & Hoeche, D., 12.2010, In: Advanced Engineering Materials. 12, 12, p. B699-B704 6 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  4. Bolt load retention and creep response of AS41 alloyed with 0.15% Ca

    Anopuo, O., Huang, Y., Hort, N., Dieringa, H. & Kainer, K. U., 08.2010, In: SAE International Journal of Materials and Manufacturing. 3, 1, p. 202-210 9 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  5. Published

    Supporting non-hierarchical supply chain networks in the electronics industry

    Scholz-Reiter, B., Heger, J., Meinecke, C., Rippel, D., Zolghadri, M. & Rasoulifar, R., 23.05.2016, 16th International Conference on Concurrent Enterprising (ICE 2010) : ‘Collaborative Environments for Sustainable Innovation’ ; Lugano, Switzerland 21-23 June 2010. Pawar, K., Canetta, L., Thoben, K. & Boer, C. (eds.). Nottingham, UK: Centre for Concurrent Enterprise, 6 p. 7477031

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  6. Extrusion benchmark 2009 experimental analysis of deflection in extrusion dies

    Pietzka, D., Ben Khalifa, N., Lorenzo, D., Tomesani, L. & Tekkaya, A. E., 2010, Advances on hot extrusion and simulation of light alloys: selected, peer reviewed papers from the International Conference on Extrusion and Benchmark (ICEB). Tekkaya, A. E. & Ben Khalifa, N. (eds.). Trans Tech Publications, Vol. 424. p. 19-26 8 p. (Key Engineering Materials; vol. 424).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  7. Accurate welding line prediction in extrusion processes

    Kloppenborg, T., Ben Khalifa, N. & Tekkaya, A. E., 2010, Advances on hot extrusion and simulation of light alloys: selected, peer reviewed papers from the International Conference on Extrusion and Benchmark (ICEB). Tekkaya, A. E. & Ben Khalifa, N. (eds.). Trans Tech Publications, Vol. 424. p. 87-95 9 p. (Key Engineering Materials; vol. 424).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  8. Simulation of the quench sensitivity of the aluminum alloy 6082

    Güzel, A., Jäger, A., Ben Khalifa, N. & Tekkaya, A. E., 2010, Advances on hot extrusion and simulation of light alloys: selected, peer reviewed papers from the International Conference on Extrusion and Benchmark (ICEB). Tekkaya, A. E. & Ben Khalifa, N. (eds.). Trans Tech Publications, Vol. 424. p. 51-56 6 p. (Key Engineering Materials; vol. 424).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  9. Direct recycling of 1050 aluminum alloy scrap material mixed with 6060 aluminum alloy chips by hot extrusion

    Güley, V., Ben Khalifa, N. & Tekkaya, A. E., 04.2010, In: International Journal of Material Forming. 3, SUPPL. 1, p. 853-856 4 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  10. Comparison of different FEM code approaches in the simulation of the die deflection during aluminium extrusion

    Donati, L., Ben Khalifa, N., Tomesani, L. & Tekkaya, A. E., 12.06.2010, In: International Journal of Material Forming. 3, SUPPL. 1, p. 375-378 4 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

Previous 1...140 141 142 143 144 145 146 147 ...167 Next