1. //
  2. Start
  3. //
  4. Publications
  5. //
  6. Browse
  7. //

Browse by research area

1631 - 1640 out of 1,843Page size: 10
Sort by: Type
  1. Published

    On the Functional Controllability Using a Geometric Approach together with a Decoupled MPC for Motion Control in Robotino

    Straßberger, D., Mercorelli, P. & Georgiadis, A., 07.2014, Proceedings of the 21st International Symposium on Mathematical Theory of Networks and Systems. Groningen: University of Groningen Press, p. 1080-1087 8 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  2. On the geometric control of internal forces in power grasps

    Prattichizzo, D., Mercorelli, P., Bicchi, A. & Vicino, A., 1997, Proceedings of the IEEE Conference on Decision and Control San Diego, Cahfomia USA December 1997 . IEEE - Institute of Electrical and Electronics Engineers Inc., Vol. 2. p. 1942-1947 6 p. (Proceedings of the IEEE Conference on Decision and Control).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  3. On the influence of settling of (ZrB2)P inoculants on Grain Refinement of Mg-alloys: Experiment and Theoretical Calculation

    Günther, R., Hartig, C., Hort, N. & Bormann, R., 2009, Linking Science and Technology for Global Solution: Proceedings of Symposia held during TMS 2009 Annual Meeting and Exhibition. The Minerals, Metals & Materials Society, p. 309-313 5 p. (Magnesium Technology).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  4. Published

    Optical part measuring inside a milling machine

    Meier, N. & Georgiadis, A., 14.05.2013, AMA Conferences 2013 Proceedings: Sensor 2013 16th International Conference on Sensors and Measurement Technology. AMA Service, p. 775-778 4 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  5. Published

    Optical part measuring inside a milling machine

    Meier, N. & Georgiadis, A., 2014, Measurement Technology and Intelligent Instruments XI. Schmitt, R. & Bosse, H. (eds.). Trans Tech Publ., p. 440-445 6 p. (Key Engineering Materials; vol. 613).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  6. Published

    Optimal scheduling for Automated Guided Vehicles (AGV) in blocking job-shops

    Heger, J. & Voß, T., 2017, Advances in Production Management Systems: The Path to Intelligent, Collaborative and Sustainable Manufacturing. Riedel, R., Thoben, K.-D., von Cieminski, G., Kiritsis, D. & Lodding, H. (eds.). Springer Verlag, Vol. 1. p. 151 - 158 8 p. (IFIP Advances in Information and Communication Technology; vol. 513).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  7. Optimal trajectory generation for camless internal combustion engine valve control

    Fabbrini, A., Doretti, D., Braune, S., Garulli, A. & Mercorelli, P., 01.11.2008, Proceedings - 34th Annual Conference of the IEEE Industrial Electronics Society, IECON 2008. IEEE - Institute of Electrical and Electronics Engineers Inc., p. 303-308 6 p. 4757970. (IEEE Industrial Electronics).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  8. Published

    Optimization Analysis for an Uncovered Wagon Transportation with an Interactive Animated Simulation-Based Platform for Multidisciplinary Learning

    Wohlstein, M. H., Zakharova, E., Block, B. M. & Mercorelli, P., 2023, Proceedings of the 15th International Conference on Computer Supported Education - Volume 2, CSEDU 2023. Jovanovic, J., Chounta, I.-A., Uhomoibhi, J. & McLaren, B. (eds.). Science and Technology Publications, Lda (SciTePress), p. 451-457 7 p. (International Conference on Computer Supported Education, CSEDU - Proceedings; vol. 2).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  9. Published

    Parameter Investigation for the In-Situ Hybridization Process by Deep Drawing of Dry Fiber-Metal-Laminates

    Kruse, M., Lehmann, J. & Ben Khalifa, N., 01.01.2023, Production at the Leading Edge of Technology: Proceedings of the 12th Congress of the German Academic Association for Production Technology (WGP), University of Stuttgart, October 2022. Liewald, M., Verl, A., Bauernhansl, T. & Möhring, H.-C. (eds.). Cham: Springer Verlag, p. 122-130 9 p. (Lecture Notes in Production Engineering; vol. Part F1163).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  10. Published

    Parameterized Synthetic Image Data Set for Fisheye Lens

    Zhen, C. & Georgiadis, A., 02.07.2018, Proceedings - 2018 5th International Conference on Information Science and Control Engineering, ICISCE 2018. Cheng, Y., Li, S. & Dai, Y. (eds.). IEEE - Institute of Electrical and Electronics Engineers Inc., p. 370-374 5 p. 8612582

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

Previous 1...160 161 162 163 164 165 166 167 ...185 Next

Recently viewed