1. //
  2. Start
  3. //
  4. Publications
  5. //
  6. Browse
  7. //

Browse by research area

311 - 320 out of 1,673Page size: 10

  1. Comparison of different FEM code approaches in the simulation of the die deflection during aluminium extrusion

    Donati, L., Ben Khalifa, N., Tomesani, L. & Tekkaya, A. E., 12.06.2010, In: International Journal of Material Forming. 3, SUPPL. 1, p. 375-378 4 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  2. Bolt load retention and creep response of AS41 alloyed with 0.15% Ca

    Anopuo, O., Huang, Y., Hort, N., Dieringa, H. & Kainer, K. U., 08.2010, In: SAE International Journal of Materials and Manufacturing. 3, 1, p. 202-210 9 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  3. Lengthscale-dependent modelling of ductile failure in metallic microstructures

    Svendsen, B., Klusemann, B. & Hortig, C., 09.2010, In: International Journal of Materials and Structural Integrity. 4, 2-4, p. 141-159 19 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  4. Published

    Methode zur Kompensierung des Streulichtanteils bei der kontinuierlichen Modulationsinterferometrie

    Klein, S., 20.09.2010, 1 ed. Göttingen: Sierke Verlag. 167 p. (Schriftenreihe zur Produkt- und Prozessinnovation; vol. 2)

    Research output: Books and anthologies › Book

  5. Characterization of grain microstructure development in the aluminum alloy EN AW-6060 during extrusion

    Kayser, T., Klusemann, B., Lambers, H. G., Maier, H. J. & Svendsen, B., 25.09.2010, In: Materials Science & Engineering A. 527, 24-25, p. 6568-6573 6 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  6. Homogenization approach based on laminates

    Klusemann, B. & Svendsen, B., 16.10.2010, PAMM: 81st Annual Meeting of the International Association of Applied Mathematics and Mechanics (GAMM). Wieners, C. (ed.). 1 ed. Wiley-VCH Verlag, Vol. 10. p. 419–420 2 p. (PAMM; vol. 10, no. 1).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  7. Simulation of stresses during casting of binary magnesium-aluminum alloys

    Pokorny, M. G., Monroe, C. A., Beckermann, C., Zhen, Z. & Hort, N., 12.2010, In: Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. 41, 12, p. 3196-3207 12 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  8. XPS studies of magnesium surfaces after exposure to Dulbecco's modified eagle medium, Hank's buffered salt solution, and simulated body fluid

    Tie, D., Feyerabend, F., Hort, N., Willumeit, R. & Hoeche, D., 12.2010, In: Advanced Engineering Materials. 12, 12, p. B699-B704 6 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  9. Published

    A Method to Enhance the Accuracy of Time of Flight Measurement Systems

    Papadoudis, J., Georgiadis, A., Koch, C. & Klein, S., 2011, Sensor + Test: short proceedings ; conferences 2011, Nürnberg Exhibition Centre, Germany, 7. - 9.6.2011 ; an event of the AMA Association for Sensor Technology. AMA. S. G. (ed.). AMA Service, Vol. 1. p. 211 1 p.

    Research output: Contributions to collected editions/works › Published abstract in conference proceedings › Research › peer-review

  10. A milp for installation scheduling of offshore wind farms

    Scholz-Reiter, B., Heger, J., Lütjen, M. & Schweizer, A., 2011, In: International Journal of Mathematical Models and Methods in Applied Sciences . 5, 2, p. 371-378 8 p.

    Research output: Journal contributions › Journal articles › Research

Previous 1...28 29 30 31 32 33 34 35 ...168 Next