Benjamin Klusemann

Prof. Dr.

Benjamin Klusemann

Contact

Prof. Dr. Benjamin Klusemann

    Research areas

  • Engineering - mechanics, process simulation, material modeling, Modeling & Simulation, continuum mechanics, finite element method
  1. 2025
  2. Published

    Generative 3D reconstruction of Ti-6Al-4V basketweave microstructures by optimization of differentiable microstructural descriptors

    Blümer, V., Safi, A. R., Soyarslan, C., Klusemann, B. & van den Boogaard, T., 01.06.2025, In: Acta Materialia. 291, 10 p., 120947.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  3. Published

    The ESAFORM benchmark 2023: interlaboratory comparison benchmark for the characterization of microstructural grain growth and dynamic recrystallization kinetics of a single-phase Ni-base superalloy

    Agirre, J., Bernal, D., Flipon, B., Bernacki, M., Brüggemann, H., Bailly, D., Merklein, M., Hagenah, H., Risse, J. H., Madej, Ł., Muszka, K., Cichocki, K., Poloczek, Ł., Bylya, O., Reshetov, A., De Micheli, P., Barlier, J., Stark, A., Suhuddin, U. F. H., Staron, P., Klusemann, B. & Galdos, L., 06.2025, In: International Journal of Material Forming. 18, 2, 36 p., 33.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  4. Published

    Fatigue life enhancement via residual stress engineering due to local forming during refill friction stir spot welding

    Becker, N., Kuhn, D., Piochowiak, J. & Klusemann, B., 01.05.2025, In: Journal of Materials Research and Technology. 36, p. 2951-2959 9 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  5. Published

    Friction surfacing of aluminum alloys on Ti6Al4V - Investigation of process parameters, material deposition behavior and bonding mechanisms

    Hoffmann, M., Roos, A. & Klusemann, B., 01.05.2025, In: Surface and Coatings Technology. 503, 12 p., 131985.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  6. Published

    Enhanced dissimilar aluminum alloy joints using 0.1 mm offset in refill friction stir spot welding

    Maranho, J. F. C., Cui, F., Tang, H., Feng, X., Luan, H., Shen, J., Wolf, W., Freitas, B. J. M., Li, W., Alcântara, N. G. D., Santos, J. F. D., Klusemann, B. & Koga, G. Y., 05.2025, In: Journal of Materials Research and Technology. 36, p. 1091-1104 14 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  7. Published

    La-Ni-H metal hydride system aging effects identification

    Shang, Y., Chen, T., Karimi, F., Le, T. T., Markmann, J., Embs, J. P., Klusemann, B., Klassen, T. & Pistidda, C., 15.04.2025, In: Chemical Engineering Journal. 510, 15 p., 161682.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  8. Published

    Impact of friction stir welding-like heat cycles on precipitates in AA7050 analysed by SAXS and numerical modelling

    Henninger, S., Chafle, R., Maawad, E., Klusemann, B., Müller, M. & Staron, P., 01.03.2025, In: Materialia. 39, 8 p., 102343.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  9. E-pub ahead of print

    Improving mechanical properties of constrained friction processing Mg-Zn-Ca alloys by modifying texture using multiple pass processing

    Chen, T., Fu, B., Suhuddin, U. F. H. R., Shen, T., Li, G., Maawad, E., Shen, J., Santos, J. F. D., Bergmann, J. P. & Klusemann, B., 10.10.2025, In: Journal of Materials Science and Technology. 232, p. 209-226 18 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  10. Published

    Effect of ambient conditions in friction surfacing

    Hoffmann, M., Duda, E. A., Aspes, P. & Klusemann, B., 02.2025, In: Welding in the World. 69, 2, p. 397-406 10 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  11. E-pub ahead of print

    Mechanical behavior, microstructural evolution and texture analysis of AA2024-T351 processed by multi-layer friction surfacing with high build rates

    Hoffmann, M., Roos, A. & Klusemann, B., 29.01.2025, (E-pub ahead of print) In: Progress in Additive Manufacturing. 15 p., 146582.

    Research output: Journal contributionsJournal articlesResearchpeer-review

Previous 1 2 3 4 5 6 7 8 ...22 Next