1. //
  2. Start
  3. //
  4. Journals
  5. //
  6. Journal of Materials Processing Technolo...
  7. //
  8. Publications
  9. //

Journal of Materials Processing Technology, ‎0924-0136

Journal

1 - 10 out of 13Page size: 10
  1. 2025
  2. Published

    Effect of consumable stud microstructure on friction surfacing: Comparison between friction extruded and hot extruded AA2024 studs

    Aspes, P., Kallien, Z., Rath, L., Suhuddin, U. & Klusemann, B., 07.2025, In: Journal of Materials Processing Technology. 341, 14 p., 118862.

    Research output: Journal contributions › Journal articles › Research › peer-review

  3. 2023
  4. Published

    Microstructural development of as-cast AM50 during Constrained Friction Processing: grain refinement and influence of process parameters

    de Castro, C. C., Shen, J., dos Santos, J. F. & Klusemann, B., 01.09.2023, In: Journal of Materials Processing Technology. 318, 11 p., 118018.

    Research output: Journal contributions › Journal articles › Research

  5. Published

    Semi-stationary shoulder bobbin-tool: A new approach in tailoring macrostructure and mechanical properties of bobbin-tool friction stir welds in magnesium alloy

    Li, G., Chen, T., Fu, B., Shen, J., Bergmann, L., Zhou, L., Chen, K., Santos, J. F. D. & Klusemann, B., 01.08.2023, In: Journal of Materials Processing Technology. 317, 117984.

    Research output: Journal contributions › Journal articles › Research

  6. 2022
  7. Published

    A multi-scaled process study of dissimilar friction stir welding of Eurofer RAFM steel to PM2000 ODS alloy

    Wang, J., Fu, B., Shen, J., Bergmann, L., Lu, X., dos Santos, J. F. & Klusemann, B., 01.09.2022, In: Journal of Materials Processing Technology. 307, 117679.

    Research output: Journal contributions › Journal articles › Research › peer-review

  8. Published

    Effect of laser peen forming process parameters on bending and surface quality of Ti-6Al-4V sheets

    Sala, S. T., Keller, S., Chupakhin, S., Pöltl, D., Klusemann, B. & Kashaev, N., 01.07.2022, In: Journal of Materials Processing Technology. 305, 16 p., 117578.

    Research output: Journal contributions › Journal articles › Research › peer-review

  9. 2021
  10. Published

    Tailoring of residual stresses by specific use of defined prestress during laser shock peening

    Schwab, K. C., Keller, S., Kashaev, N. & Klusemann, B., 01.09.2021, In: Journal of Materials Processing Technology. 295, 11 p., 117154.

    Research output: Journal contributions › Journal articles › Research › peer-review

  11. 2020
  12. Published

    Production of aluminum AA7075/6060 compounds by die casting and hot extrusion

    Greß, T., Mittler, T., Chen, H., Stahl, J., Schmid, S., Ben Khalifa, N. & Volk, W., 01.06.2020, In: Journal of Materials Processing Technology. 280, 12 p., 116594.

    Research output: Journal contributions › Journal articles › Research › peer-review

  13. 2019
  14. Published

    Analytical prediction of wall thickness reduction and forming forces during the radial indentation process in Incremental Profile Forming

    Grzancic, G., Löbbe, C., Ben Khalifa, N. & Tekkaya, A. E., 05.2019, In: Journal of Materials Processing Technology. 267, p. 68-79 12 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  15. 2018
  16. Published

    Experimental and numerical investigation of residual stresses in laser shock peened AA2198

    Keller, S., Chupakhin, S., Staron, P., Maawad, E., Kashaev, N. & Klusemann, B., 01.05.2018, In: Journal of Materials Processing Technology. 255, p. 294-307 14 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  17. 2016

  18. Granular media-based tube press hardening

    Chen, H., Güner, A., Ben Khalifa, N. & Tekkaya, A. E., 01.02.2016, In: Journal of Materials Processing Technology. 228, p. 145-159 15 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

Previous 1 2 Next

Recently viewed

Publications

  1. A conceptual cross-disciplinary model of organizational practices for older workers
  2. Leere untern Tannenbaum
  3. Sense of Place in Spatial Planning
  4. Fatigue life enhancement via residual stress engineering due to local forming during refill friction stir spot welding
  5. Explaining energy transition
  6. Relationships between oncoming traffic intensity, subjective predictions about oncoming traffic, and intentions to overtake
  7. The Use of Culture in Education
  8. Complexity Measures of Traffic Scenarios
  9. Hot rolling and deep drawing of AM50 sheet
  10. Introduction
  11. Karl Mays Orientzyklus
  12. The dynamics of prioritizing
  13. Technology Development and Stakeholder Influence
  14. Formulating and solving integrated order batching and routing in multi-depot AGV-assisted mixed-shelves warehouses
  15. Schulleitungsmonitor Schweiz 2022
  16. Towards a future conceptualization of destination resilience
  17. X Machina and the World of Tomorrow
  18. Effect of ECAP Process on the Activation of Deformation Mechanisms During Subsequent Uniaxial Tension of Mg-ZEWK2000 Sheets
  19. How digital reflection and feedback environments contribute to pre-service teachers’ beliefs during a teaching practicum
  20. Computerspiele
  21. ‘Then you just have to perform better’
  22. Correction to
  23. Fast response of groundwater to heavy rainfall
  24. Impact of different methods of heathland management on the nutrient balance and vegetation dynamics
  25. European Management Styles: Gaining Insights from Stereotypes
  26. Self-selection, socialization, and risk perception
  27. Effect of extrusion and rotary swaging on the microstructural evolution and properties of Mg-5Li-5.3Al-0.7Si alloy
  28. Navigating tensions in inclusive conservation
  29. Employing complementary multivariate methods for a designed nontarget LC-HRMS screening of a wastewater-influenced river
  30. The use of the entropy concept in ecological economics
  31. The complex spatio-temporal dynamics of organic micropollutants in tidal rivers
  32. Influence of One Hour versus Two Hours of Daily Static Stretching for Six Weeks Using a Calf-Muscle-Stretching Orthosis on Maximal Strength
  33. Towards a comparative international history of dockers
  34. Semi-infinite Optimierung
  35. Tree resin composition, collection behavior and selective filters shape chemical profiles of tropical bees (Apidae: Meliponini)
  36. Does adhering to the principles of green finance matter for stock valuation? Evidence from testing for (co-)explosiveness
  37. Formative assessment in mathematics