Modeling of a thermomechanical process chain for sheet steels

Research output: Journal contributionsJournal articlesResearchpeer-review

Standard

Modeling of a thermomechanical process chain for sheet steels. / Barthel, C.; Klusemann, B.; Denzer, R. et al.
In: International Journal of Mechanical Sciences, Vol. 74, 09.2013, p. 46-54.

Research output: Journal contributionsJournal articlesResearchpeer-review

Harvard

APA

Vancouver

Barthel C, Klusemann B, Denzer R, Svendsen B. Modeling of a thermomechanical process chain for sheet steels. International Journal of Mechanical Sciences. 2013 Sept;74:46-54. doi: 10.1016/j.ijmecsci.2013.04.006

Bibtex

@article{de5b97a210914b91a085866bdb8f2cb2,
title = "Modeling of a thermomechanical process chain for sheet steels",
abstract = "The purpose of this work is the development, identification and validation of a model for the simulation of a thermomechanical multistage production process chain for sheet steels. The process of interest consists of forming (in particular deep-drawing) followed by cutting and heat treatment. For the forming and cutting stages, the complete model is based in particular on a model for thermoelastic, viscoplastic (i.e., rate-dependent) material behavior in sheet steels accounting for isotropic and anisotropic (i.e., kinematic and cross) hardening. This is combined with a model for thermally induced phase transformations in order to model heat treatment. The particular material modeled here is the sheet steel LH800{\textregistered}. This steel has an initially ferritic microstructure which is maintained during forming and cutting. Heating of the workpiece after forming and cutting during heat treatment phase results in transformation of ferrite to austenite. Subsequent air-cooling back to room temperature is accompanied by a second transformation from austenite to martensite. Model predictions for the workpiece behavior during forming and cutting show quite good agreement with corresponding experimental results. In contrast, small discrepancies between the model predictions and experimental results for the change in workpiece geometry during cooling imply that the phase transformation from austenite to martensite in LH800{\textregistered} is not purely volumetric in nature as assumed in the model. Rather, it results in change in the deviatoric state of stress in the material and a corresponding change in shape of the workpiece.",
keywords = "Anisotropic hardening, Phase change, Rate dependence, Sheet steel, Thermomechanical process chain, Engineering",
author = "C. Barthel and B. Klusemann and R. Denzer and B. Svendsen",
year = "2013",
month = sep,
doi = "10.1016/j.ijmecsci.2013.04.006",
language = "English",
volume = "74",
pages = "46--54",
journal = "International Journal of Mechanical Sciences",
issn = "0020-7403",
publisher = "Elsevier Ltd",

}

RIS

TY - JOUR

T1 - Modeling of a thermomechanical process chain for sheet steels

AU - Barthel, C.

AU - Klusemann, B.

AU - Denzer, R.

AU - Svendsen, B.

PY - 2013/9

Y1 - 2013/9

N2 - The purpose of this work is the development, identification and validation of a model for the simulation of a thermomechanical multistage production process chain for sheet steels. The process of interest consists of forming (in particular deep-drawing) followed by cutting and heat treatment. For the forming and cutting stages, the complete model is based in particular on a model for thermoelastic, viscoplastic (i.e., rate-dependent) material behavior in sheet steels accounting for isotropic and anisotropic (i.e., kinematic and cross) hardening. This is combined with a model for thermally induced phase transformations in order to model heat treatment. The particular material modeled here is the sheet steel LH800®. This steel has an initially ferritic microstructure which is maintained during forming and cutting. Heating of the workpiece after forming and cutting during heat treatment phase results in transformation of ferrite to austenite. Subsequent air-cooling back to room temperature is accompanied by a second transformation from austenite to martensite. Model predictions for the workpiece behavior during forming and cutting show quite good agreement with corresponding experimental results. In contrast, small discrepancies between the model predictions and experimental results for the change in workpiece geometry during cooling imply that the phase transformation from austenite to martensite in LH800® is not purely volumetric in nature as assumed in the model. Rather, it results in change in the deviatoric state of stress in the material and a corresponding change in shape of the workpiece.

AB - The purpose of this work is the development, identification and validation of a model for the simulation of a thermomechanical multistage production process chain for sheet steels. The process of interest consists of forming (in particular deep-drawing) followed by cutting and heat treatment. For the forming and cutting stages, the complete model is based in particular on a model for thermoelastic, viscoplastic (i.e., rate-dependent) material behavior in sheet steels accounting for isotropic and anisotropic (i.e., kinematic and cross) hardening. This is combined with a model for thermally induced phase transformations in order to model heat treatment. The particular material modeled here is the sheet steel LH800®. This steel has an initially ferritic microstructure which is maintained during forming and cutting. Heating of the workpiece after forming and cutting during heat treatment phase results in transformation of ferrite to austenite. Subsequent air-cooling back to room temperature is accompanied by a second transformation from austenite to martensite. Model predictions for the workpiece behavior during forming and cutting show quite good agreement with corresponding experimental results. In contrast, small discrepancies between the model predictions and experimental results for the change in workpiece geometry during cooling imply that the phase transformation from austenite to martensite in LH800® is not purely volumetric in nature as assumed in the model. Rather, it results in change in the deviatoric state of stress in the material and a corresponding change in shape of the workpiece.

KW - Anisotropic hardening

KW - Phase change

KW - Rate dependence

KW - Sheet steel

KW - Thermomechanical process chain

KW - Engineering

UR - http://www.scopus.com/inward/record.url?scp=84880572501&partnerID=8YFLogxK

UR - https://www.mendeley.com/catalogue/73fe0d3a-3e15-3e20-8d33-8d11611466e9/

U2 - 10.1016/j.ijmecsci.2013.04.006

DO - 10.1016/j.ijmecsci.2013.04.006

M3 - Journal articles

AN - SCOPUS:84880572501

VL - 74

SP - 46

EP - 54

JO - International Journal of Mechanical Sciences

JF - International Journal of Mechanical Sciences

SN - 0020-7403

ER -

Recently viewed

Publications

  1. Effects of grade retention on achievement and self-concept in science and mathematics
  2. Engaging creatively with tension in collaborative research
  3. Der Zentrale Runde Tisch der DDR: Wortprotokoll und Dokumente
  4. Does a smile open all doors? Understanding the impact of appearance disclosure on accommodation sharing platforms
  5. Drivers of above-ground understorey biomass and nutrient stocks in temperate deciduous forests
  6. Comfortable Time Headways under Different Visibility Conditions
  7. Assessment of model uncertainty during the river export modelling of pesticides and transformation products
  8. German Version of the Relationship Problems Questionnaire
  9. Collectivizing Convenience?
  10. Utilities' Business Models for Renewable Energy
  11. The impact of auditor rotation, audit firm rotation and non-audit services on earnings quality, audit quality and investor perceptions: A literature review
  12. Instruments of labour law
  13. Mehr Wirtschaftlichkeit durch Systemwechsel?
  14. The New Media
  15. Just what are temperate and boreal rainforests?
  16. An empirical note on wages in an internal labour market
  17. A meta‐analysis on the effects of just‐below versus round prices
  18. Does Internet-based guided self-help for depression cause harm?
  19. The impact of digitisation and big data analysis on the sustainable development of tourism and its environmental impact
  20. Metaphern zur Klärung biologischer Phänomene
  21. Lagrangian studies of coherent sets and heat transport in constant heat flux-driven turbulent Rayleigh-Bénard convection
  22. Leverage points for sustainability transformations
  23. Actor perceptions of polycentricity in wind power governance
  24. Restoring the human capacity for conserving biodiversity
  25. Magnesium alloy containing silver for degradable biomedical implants
  26. § 354 Verwirkungsklausel
  27. Qualitative human error analysis in medicine
  28. Der gefühlte Anspruch in der Haftpflichtversicherung
  29. How do refugees use their social capital for successful labor market integration?