Feasibility Study of Solid-State Recycling through Direct Hot Rolling of AA5754 Aluminum Chips for Automotive Applications

El Mehtedi, M., Buonadonna, P., El Mohtadi, R., Loi, G., Aymerich, F., Ben Khalifa, N. & Carta, M., 01.10.2024, Aluminum, Polymers, Composites and Additive Manufacturing. Omatsu, T., Donati, L., Alin Sirbu, N. & Ali, A. (eds.). Trans Tech Publications Ltd, p. 3-12 10 p. (Materials Science Forum; vol. 1130).

Research output: Contributions to collected editions/works › Chapter › peer-review

Neural network-based estimation and compensation of friction for enhanced deep drawing process control

Thiery, S., Zein El Abdine, M., Heger, J. & Ben Khalifa, N., 15.05.2024, Material Forming ESAFORM 2024: The 27th International ESAFORM Conference on Material Forming – ESAFORM 2024 – held in Toulouse (France), at the Pierre Baudis Convention Center between 24-26th April, 2024. Araujo, A. C., Cantarel, A., Chabert, F., Korycki, A., Olivier, P. & Schmidt, F. (eds.). Millersville: MaterialsResearchForum LLC, p. 1462-1471 10 p. 162. (Materials Research Proceedings; vol. 41).

Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

Deep Rolling for Tailoring Residual Stresses of AA2024 Sheet Metals

Lehmann, J., Keller, S., Esterl, F., Kashaev, N., Klusemann, B. & Ben Khalifa, N., 2024, Proceedings of the 14th International Conference on the Technology of Plasticity - Current Trends in the Technology of Plasticity: ICTP 2023 - Volume 3. Mocellin, K., Bouchard, P-O., Bigot, R. & Balan, T. (eds.). Cham: Springer International Publishing AG, Vol. 3. p. 352-362 11 p. (Lecture Notes in Mechanical Engineering).

Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

Development of a Parameterized Model for Additively Manufactured Dies to Control the Strains in Extrudates

Esterl, F., Nienaber, M., Bohlen, J. & Ben Khalifa, N., 2024, Thirteenth International Aluminum Extrusion Technology Seminar (ET'24): April 30 - May 02 2024, Orlando, Florida, USA. Extrusion Technology for Aluminum Profiles Foundation, Vol. 1. p. 1-8 8 p. RD467

Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

Effect of ECAP Process on the Activation of Deformation Mechanisms During Subsequent Uniaxial Tension of Mg-ZEWK2000 Sheets

Victoria-Hernandez, J., Cano-Castillo, G., Böhm, V., Gruber, M., Volk, W., Ben Khalifa, N. & Letzig, D., 2024, Proceedings of the 14th International Conference on the Technology of Plasticity - Current Trends in the Technology of Plasticity: ICTP 2023 - Volume 4. Mocellin, K., Bouchard, P-O., Bigot, R. & Balan, T. (eds.). Cham: Springer International Publishing AG, Vol. 4. p. 744-753 10 p. (Lecture Notes in Mechanical Engineering).

Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

Experimental and Numerical Investigation of the Forming Zone in Dieless Wire Drawing Process of Thin Biometallic Wires

Braatz, M., Bohlen, J. & Ben Khalifa, N., 2024, Proceedings of the 14th International Conference on the Technology of Plasticity - Current Trends in the Technology of Plasticity - ICTP 2023 - Volume 1. Mocellin, K., Bouchard, P-O., Bigot, R. & Balan, T. (eds.). Springer Science and Business Media Deutschland GmbH, Vol. Volume 1. p. 479-490 12 p. (Lecture Notes in Mechanical Engineering).

Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review