Materials Science and Engineering A, ‎0921-5093

Journal

  1. 2013
  2. Effect of die design on the welding quality during solid state recycling of AA6060 chips by hot extrusion

    Güley, V., Güzel, A., Jäger, A., Ben Khalifa, N., Tekkaya, A. E. & Misiolek, W. Z., 01.07.2013, In: Materials Science & Engineering A. 574, p. 163-175 13 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  3. 2012
  4. Hot deformation behavior of Mg-2Sn-2Ca alloy in as-cast condition and after homogenization

    Rao, K. P., Prasad, Y. V. R. K., Suresh, K., Hort, N. & Kainer, K. U., 30.08.2012, In: Materials Science and Engineering A. 552, p. 444-450 7 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  5. Improving mechanical properties of chip-based aluminum extrudates by integrated extrusion and equal channel angular pressing (iECAP)

    Haase, M., Ben Khalifa, N., Tekkaya, A. E. & Misiolek, W. Z., 30.03.2012, In: Materials Science & Engineering A. 539, p. 194-204 11 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  6. 2011
  7. Compressive strength and hot deformation behavior of TX32 magnesium alloy with 0.4% Al and 0.4% Si additions

    Rao, K. P., Prasad, Y. V. R. K., Dharmendra, C., Hort, N. & Kainer, K. U., 25.08.2011, In: Materials Science and Engineering A. 528, 22-23, p. 6964-6970 7 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  8. Effect of yttrium addition on lattice parameter, Young's modulus and vacancy of magnesium

    Peng, Q., Meng, J., Li, Y., Huang, Y. & Hort, N., 25.02.2011, In: Materials Science and Engineering A. 528, 4-5, p. 2106-2109 4 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  9. 2010
  10. Characterization of grain microstructure development in the aluminum alloy EN AW-6060 during extrusion

    Kayser, T., Klusemann, B., Lambers, H. G., Maier, H. J. & Svendsen, B., 25.09.2010, In: Materials Science & Engineering A. 527, 24-25, p. 6568-6573 6 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  11. 2009
  12. Investigation of minimum creep rates and stress exponents calculated from tensile and compressive creep data of magnesium alloy AE42

    Dieringa, H., Hort, N. & Kainer, K. U., 15.06.2009, In: Materials Science and Engineering A. 510-511, C, p. 382-386 5 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  13. Optimum parameters and rate-controlling mechanisms for hot working of extruded Mg-3Sn-1Ca alloy

    Prasad, Y. V. R. K., Rao, K. P., Hort, N. & Kainer, K. U., 25.02.2009, In: Materials Science and Engineering A. 502, 1-2, p. 25-31 7 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  14. 2007
  15. Creep behavior of AE42 based hybrid composites

    Arunachaleswaran, A., Pereira, I. M., Dieringa, H., Huang, Y., Hort, N., Dhindaw, B. K. & Kainer, K. U., 15.07.2007, In: Materials Science and Engineering A. 460-461, p. 268-276 9 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  16. 2005
  17. Tensile and compressive creep behaviour of Al2O3 (Saffil®) short fiber reinforced magnesium alloy AE42

    Dieringa, H., Huang, Y., Maier, P., Hort, N. & Kainer, K. U., 25.11.2005, In: Materials Science and Engineering A. 410-411, p. 85-88 4 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

Previous 1 2 3 4 Next

Recently viewed

Publications

  1. Continuous 3D scanning mode using servomotors instead of stepping motors in dynamic laser triangulation
  2. A decoupled MPC using a geometric approach and feedforward action for motion control in robotino
  3. Situated multiplying in primary school
  4. Dynamically changing sequencing rules with reinforcement learning in a job shop system with stochastic influences
  5. Long-term memory predictors of adult language learning at the interface between syntactic form and meaning
  6. Early Detection of Faillure in Conveyor Chain Systems by Wireless Sensor Node
  7. A Switching Cascade Sliding PID-PID Controllers Combined with a Feedforward and an MPC for an Actuator in Camless Internal Combustion Engines
  8. Transductive support vector machines for structured variables
  9. Selecting and Adapting Methods for Analysis and Design in Value-Sensitive Digital Social Innovation Projects: Toward Design Principles
  10. Accounting and Modeling as Design Metaphors for CEMIS
  11. Taking notes as a strategy for solving reality-based tasks in mathematics
  12. Special Issue The Discourse of Redundancy Introduction
  13. Towards a Global Script?
  14. Correlation of Microstructure and Local Mechanical Properties Along Build Direction for Multi-layer Friction Surfacing of Aluminum Alloys
  15. Multiphase-field modeling of temperature-driven intermetallic compound evolution in an Al-Mg system for application to solid-state joining processes
  16. Sliding-Mode-Based Input-Output Linearization of a Peltier Element for Ice Clamping Using a State and Disturbance Observer