Materials Science and Engineering A, ‎0921-5093

Journal

  1. 2020
  2. Achieving enhanced mechanical properties in Mg-Gd-Y-Zn-Mn alloy by altering dynamic recrystallization behavior via pre-ageing treatment

    Wang, K., Dou, X., Wang, J., Huang, Y., Gavras, S., Hort, N., Liu, S., Hu, H., Wang, J. & Pan, F., 14.07.2020, In: Materials Science and Engineering A. 790, 139635.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  3. Effect of biaxial compressive stress state on the microstructure evolution and deformation compatibility of rolled sheet Mg alloy AZ31 at room temperature

    Xia, D., Zhang, J., Chen, X., Huang, G., Jiang, B., Tang, A., Gavras, S., Huang, Y., Hort, N. & Pan, F., 03.07.2020, In: Materials Science and Engineering A. 789, 139599.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  4. In situ compressive investigations on the effects of solid solution Gd on the texture and lattice strain evolution of Mg

    Xu, Y., Huang, Y., Zhong, Z., You, S., Gan, W., Xiao, B., Maawad, E., Schell, N., Gensch, F., Pan, F. & Hort, N., 13.02.2020, In: Materials Science and Engineering A. 774, 138938.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  5. Published

    Microstructure by design: An approach of grain refinement and isotropy improvement in multi-layer wire-based laser metal deposition

    Froend, M., Ventzke, V., Dorn, F., Kashaev, N., Klusemann, B. & Enz, J., 20.01.2020, In: Materials Science and Engineering A. 772, 13 p., 138635.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  6. 2019
  7. Abnormal extrusion texture and reversed yield asymmetry in a Mg–Y-Sm-Zn-Zr alloy

    Lyu, S., Zheng, R., Xiao, W., Huang, Y., Gavras, S., Hort, N., Li, G. & Ma, C., 08.07.2019, In: Materials Science and Engineering A. 760, p. 426-430 5 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  8. Microscopic deformation compatibility during biaxial tension in AZ31 Mg alloy rolled sheet at room temperature

    Xia, D., Huang, G., Liu, S., Tang, A., Gavras, S., Huang, Y., Hort, N., Jiang, B. & Pan, F., 22.05.2019, In: Materials Science and Engineering A. 756, p. 1-10 10 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  9. Published

    Mechanical characterization of as-cast AA7075/6060 and CuSn6/Cu99.5 compounds using an experimental and numerical push-out test

    Greß, T., Stahl, J., Mittler, T., Spano, L., Chen, H., Ben Khalifa, N. & Volk, W., 28.03.2019, In: Materials Science & Engineering A. 751, p. 214-225 12 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  10. 2017
  11. As cast microstructures on the mechanical and corrosion behaviour of ZK40 modified with Gd and Nd additions

    Buzolin, R. H., Mohedano, M., Mendis, C. L., Mingo, B., Tolnai, D., Blawert, C., Kainer, K. U., Pinto, H. & Hort, N., 13.01.2017, In: Materials Science and Engineering A. 682, p. 238-247 10 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  12. 2016
  13. In situ synchrotron radiation diffraction investigation of the compression behaviour at 350 °C of ZK40 alloys with addition of CaO and Y

    Buzolin, R. H., Mendis, C. L., Tolnai, D., Stark, A., Schell, N., Pinto, H., Kainer, K. U. & Hort, N., 10.05.2016, In: Materials Science and Engineering A. 664, p. 2-9 8 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  14. Microstructure evolution of Mg-11Gd-4.5Y-1Nd-1.5Zn-0.5Zr (wt%) alloy during deformation and its effect on strengthening

    Yu, Z., Huang, Y., Gan, W., Mendis, C. L., Zhong, Z., Brokmeier, H. G., Hort, N. & Meng, J., 07.03.2016, In: Materials Science and Engineering A. 657, p. 259-268 10 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

Recently viewed

Publications

  1. Some model properties to control a permanent magnet machine using a controlled invariant subspace
  2. Linux-based Embedded System for Wavelet Denoising and Monitoring of sEMG Signals using an Axiomatic Seminorm
  3. A Gait Pattern Generator for Closed-Loop Position Control of a Soft Walking Robot
  4. A two-stage Kalman estimator for motion control using model predictive strategy
  5. Control of the inverse pendulum based on sliding mode and model predictive control
  6. Anatomy of Haar Wavelet Filter and Its Implementation for Signal Processing
  7. Using sequential injection analysis for fast determination of phosphate in coastal waters
  8. Primary Side Circuit Design of a Multi-coil Inductive System for Powering Wireless Sensors
  9. Mathematical relation between extended connectivity and eigenvector coefficients.
  10. Evolutionary cost-tolerance optimization for complex assembly mechanisms via simulation and surrogate modeling approaches
  11. Dynamically adjusting the k-values of the ATCS rule in a flexible flow shop scenario with reinforcement learning
  12. A Switching Cascade Sliding PID-PID Controllers Combined with a Feedforward and an MPC for an Actuator in Camless Internal Combustion Engines
  13. Toward Application and Implementation of in Silico Tools and Workflows within Benign by Design Approaches
  14. Switching Dispatching Rules with Gaussian Processes
  15. Holistic and scalable ranking of RDF data
  16. Comparison of different FEM codes approach for extrusion process analysis
  17. Modeling of lateness distributions depending on the sequencing method with respect to productivity effects
  18. Multi-view discriminative sequential learning
  19. Segment Introduction