Biomechanical characteristics of the porcine denticulate ligament in different vertebral levels of the cervical spine-Preliminary results of an experimental study

Research output: Journal contributionsJournal articlesResearchpeer-review

Standard

Biomechanical characteristics of the porcine denticulate ligament in different vertebral levels of the cervical spine-Preliminary results of an experimental study. / Polak, Katarzyna; Czyż , Marcin ; Ścigała , Krzysztof et al.
In: Journal of the Mechanical Behavior of Biomedical Materials, Vol. 34, 06.2014, p. 165-170.

Research output: Journal contributionsJournal articlesResearchpeer-review

Harvard

APA

Vancouver

Bibtex

@article{cca9473e042c454fa915a63a4c857b17,
title = "Biomechanical characteristics of the porcine denticulate ligament in different vertebral levels of the cervical spine-Preliminary results of an experimental study",
abstract = "Background: Few studies exist on the mechanical properties of denticulate ligaments and none report the variation in these properties at different levels of the spine. The aim of this study was to perform an experimental determination of load-extension and stress-strain characteristics of the denticulate ligament and to establish if their properties change at different vertebral levels of the cervical spine. Method: The study was carried out on a total of 98 porcine denticulate ligament samples dissected from seven fresh porcine cervical spinal cord specimens. All of the samples were subjected to an uniaxial tensile test at a speed of 2. mm/min, during which the load-extension characteristics were registered. Results: The analysis revealed a decrease of the failure force in the caudal orientation indicated by significant differences between the C1 (1.04±0.41. N) and C7 (0.55±0.12. N) vertebral levels (P=0.037). The average ultimate force that broke the denticulate ligaments was 0.88. N. The mean value of Young[U+05F3]s modulus was 2.06. MPa with a minimum of 1.31. MPa for C7 and maximum of 2.46. MPa for C5. Conclusions: The values of the denticulate ligament failure force in samples from different cervical vertebrae levels differ significantly. The presented data should be taken into consideration during numerical modelling of the human cervical spinal cord.",
keywords = "Engineering, Cervical spinal cord; Denticulate ligament; Experimental study; Mechanical properties; Numerical modelling; Spinal cord; Uniaxial tensile test",
author = "Katarzyna Polak and Marcin Czy{\.z} and Krzysztof {\'S}ciga{\l}a and W{\l}odzimierz Jarmundowicz and Romuald B{\c e}dzi{\'n}ski",
year = "2014",
month = jun,
doi = "10.1016/j.jmbbm.2014.02.010",
language = "English",
volume = "34",
pages = "165--170",
journal = "Journal of the Mechanical Behavior of Biomedical Materials",
issn = "1878-0180",
publisher = "Elsevier B.V.",

}

RIS

TY - JOUR

T1 - Biomechanical characteristics of the porcine denticulate ligament in different vertebral levels of the cervical spine-Preliminary results of an experimental study

AU - Polak, Katarzyna

AU - Czyż , Marcin

AU - Ścigała , Krzysztof

AU - Jarmundowicz , Włodzimierz

AU - Będziński , Romuald

PY - 2014/6

Y1 - 2014/6

N2 - Background: Few studies exist on the mechanical properties of denticulate ligaments and none report the variation in these properties at different levels of the spine. The aim of this study was to perform an experimental determination of load-extension and stress-strain characteristics of the denticulate ligament and to establish if their properties change at different vertebral levels of the cervical spine. Method: The study was carried out on a total of 98 porcine denticulate ligament samples dissected from seven fresh porcine cervical spinal cord specimens. All of the samples were subjected to an uniaxial tensile test at a speed of 2. mm/min, during which the load-extension characteristics were registered. Results: The analysis revealed a decrease of the failure force in the caudal orientation indicated by significant differences between the C1 (1.04±0.41. N) and C7 (0.55±0.12. N) vertebral levels (P=0.037). The average ultimate force that broke the denticulate ligaments was 0.88. N. The mean value of Young[U+05F3]s modulus was 2.06. MPa with a minimum of 1.31. MPa for C7 and maximum of 2.46. MPa for C5. Conclusions: The values of the denticulate ligament failure force in samples from different cervical vertebrae levels differ significantly. The presented data should be taken into consideration during numerical modelling of the human cervical spinal cord.

AB - Background: Few studies exist on the mechanical properties of denticulate ligaments and none report the variation in these properties at different levels of the spine. The aim of this study was to perform an experimental determination of load-extension and stress-strain characteristics of the denticulate ligament and to establish if their properties change at different vertebral levels of the cervical spine. Method: The study was carried out on a total of 98 porcine denticulate ligament samples dissected from seven fresh porcine cervical spinal cord specimens. All of the samples were subjected to an uniaxial tensile test at a speed of 2. mm/min, during which the load-extension characteristics were registered. Results: The analysis revealed a decrease of the failure force in the caudal orientation indicated by significant differences between the C1 (1.04±0.41. N) and C7 (0.55±0.12. N) vertebral levels (P=0.037). The average ultimate force that broke the denticulate ligaments was 0.88. N. The mean value of Young[U+05F3]s modulus was 2.06. MPa with a minimum of 1.31. MPa for C7 and maximum of 2.46. MPa for C5. Conclusions: The values of the denticulate ligament failure force in samples from different cervical vertebrae levels differ significantly. The presented data should be taken into consideration during numerical modelling of the human cervical spinal cord.

KW - Engineering

KW - Cervical spinal cord; Denticulate ligament; Experimental study; Mechanical properties; Numerical modelling; Spinal cord; Uniaxial tensile test

UR - http://www.scopus.com/inward/record.url?scp=84896836833&partnerID=8YFLogxK

U2 - 10.1016/j.jmbbm.2014.02.010

DO - 10.1016/j.jmbbm.2014.02.010

M3 - Journal articles

C2 - 24583921

VL - 34

SP - 165

EP - 170

JO - Journal of the Mechanical Behavior of Biomedical Materials

JF - Journal of the Mechanical Behavior of Biomedical Materials

SN - 1878-0180

ER -