Effect of filler wire and post weld heat treatment on the mechanical properties of laser beam-welded AA2198

Research output: Journal contributionsJournal articlesResearchpeer-review

Standard

Effect of filler wire and post weld heat treatment on the mechanical properties of laser beam-welded AA2198. / Examilioti, Theano N.; Kashaev, Nikolai; Ventzke, Volker et al.
In: Materials Characterization, Vol. 178, 111257, 01.08.2021.

Research output: Journal contributionsJournal articlesResearchpeer-review

Harvard

APA

Vancouver

Bibtex

@article{f17227d9abbe43acaa07fa893670a7be,
title = "Effect of filler wire and post weld heat treatment on the mechanical properties of laser beam-welded AA2198",
abstract = "The mechanical behavior of autogenously and non-autogenously laser beam-welded joints of Al-Cu-Li alloy AA2198 and the effect of post weld heat treatment are examined in this contribution. The deformation texture of the base material does not present any significant change in the macrotexture with applying different artificial ageing times. Autogenously and non-autogenously laser beam-welded joints present a decrease in yield stress and ultimate strength in the as-welded condition, approximately 45% and 36–38%, respectively, when compared with AA2198-Τ3 base material. The addition of the AA4047 filler wire increases the Si and Cu content in the grain interior and in the grain boundaries of the fusion zone of the welded joint. Micro-hardness measurements for autogenously laser-welded joints showed a decrease in hardness by 27% for the fusion zone and 42% for the heat-affected zone, when compared with the non-autogenously laser beam-welded joints. Α quality index was exploited to evaluate the tensile mechanical performance of the welded joints. It is observed that the non-autogenously welded joints always show a higher {\textquoteleft}quality{\textquoteright} than the respective autogenously welded joints and the highest quality index in terms of mechanical performance is achieved for the as-welded and the peak-aged conditions, respectively. Regardless of the post weld heat treatment condition, both autogenously and non-autogenously laser-welded specimens fractured in between the equiaxed and fusion zone during tensile loading.",
keywords = "Laser beam-welding, Post-weld heat treatment, Mechanical properties, Microhardness, Microstructure, Al--Li alloy, Engineering",
author = "Examilioti, {Theano N.} and Nikolai Kashaev and Volker Ventzke and Benjamin Klusemann and Alexopoulos, {Nikolaos D.}",
note = "Publisher Copyright: {\textcopyright} 2021 Elsevier Inc.",
year = "2021",
month = aug,
day = "1",
doi = "10.1016/j.matchar.2021.111257",
language = "English",
volume = "178",
journal = "Materials Characterization",
issn = "1044-5803",
publisher = "Elsevier Ltd",

}

RIS

TY - JOUR

T1 - Effect of filler wire and post weld heat treatment on the mechanical properties of laser beam-welded AA2198

AU - Examilioti, Theano N.

AU - Kashaev, Nikolai

AU - Ventzke, Volker

AU - Klusemann, Benjamin

AU - Alexopoulos, Nikolaos D.

N1 - Publisher Copyright: © 2021 Elsevier Inc.

PY - 2021/8/1

Y1 - 2021/8/1

N2 - The mechanical behavior of autogenously and non-autogenously laser beam-welded joints of Al-Cu-Li alloy AA2198 and the effect of post weld heat treatment are examined in this contribution. The deformation texture of the base material does not present any significant change in the macrotexture with applying different artificial ageing times. Autogenously and non-autogenously laser beam-welded joints present a decrease in yield stress and ultimate strength in the as-welded condition, approximately 45% and 36–38%, respectively, when compared with AA2198-Τ3 base material. The addition of the AA4047 filler wire increases the Si and Cu content in the grain interior and in the grain boundaries of the fusion zone of the welded joint. Micro-hardness measurements for autogenously laser-welded joints showed a decrease in hardness by 27% for the fusion zone and 42% for the heat-affected zone, when compared with the non-autogenously laser beam-welded joints. Α quality index was exploited to evaluate the tensile mechanical performance of the welded joints. It is observed that the non-autogenously welded joints always show a higher ‘quality’ than the respective autogenously welded joints and the highest quality index in terms of mechanical performance is achieved for the as-welded and the peak-aged conditions, respectively. Regardless of the post weld heat treatment condition, both autogenously and non-autogenously laser-welded specimens fractured in between the equiaxed and fusion zone during tensile loading.

AB - The mechanical behavior of autogenously and non-autogenously laser beam-welded joints of Al-Cu-Li alloy AA2198 and the effect of post weld heat treatment are examined in this contribution. The deformation texture of the base material does not present any significant change in the macrotexture with applying different artificial ageing times. Autogenously and non-autogenously laser beam-welded joints present a decrease in yield stress and ultimate strength in the as-welded condition, approximately 45% and 36–38%, respectively, when compared with AA2198-Τ3 base material. The addition of the AA4047 filler wire increases the Si and Cu content in the grain interior and in the grain boundaries of the fusion zone of the welded joint. Micro-hardness measurements for autogenously laser-welded joints showed a decrease in hardness by 27% for the fusion zone and 42% for the heat-affected zone, when compared with the non-autogenously laser beam-welded joints. Α quality index was exploited to evaluate the tensile mechanical performance of the welded joints. It is observed that the non-autogenously welded joints always show a higher ‘quality’ than the respective autogenously welded joints and the highest quality index in terms of mechanical performance is achieved for the as-welded and the peak-aged conditions, respectively. Regardless of the post weld heat treatment condition, both autogenously and non-autogenously laser-welded specimens fractured in between the equiaxed and fusion zone during tensile loading.

KW - Laser beam-welding

KW - Post-weld heat treatment

KW - Mechanical properties

KW - Microhardness

KW - Microstructure

KW - Al--Li alloy

KW - Engineering

UR - http://www.scopus.com/inward/record.url?scp=85117624113&partnerID=8YFLogxK

U2 - 10.1016/j.matchar.2021.111257

DO - 10.1016/j.matchar.2021.111257

M3 - Journal articles

VL - 178

JO - Materials Characterization

JF - Materials Characterization

SN - 1044-5803

M1 - 111257

ER -