1. //
  2. Start
  3. //
  4. Publications
  5. //
  6. Browse
  7. //

Browse by research area

1281 - 1300 out of 1,867Page size: 20
  1. Published

    Optical part measuring inside a milling machine

    Meier, N. & Georgiadis, A., 2014, Measurement Technology and Intelligent Instruments XI. Schmitt, R. & Bosse, H. (eds.). Trans Tech Publ., p. 440-445 6 p. (Key Engineering Materials; vol. 613).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  2. Published

    Parameters identification in a permanent magnet three-phase synchronous motor of a city-bus for an intelligent drive assistant

    Mercorelli, P., 2014, In: International Journal of Modelling, Identification and Control. 21, 4, p. 352-361 10 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  3. Published

    Programmierung einer DELTA-Roboterzelle nach PackML Standard

    Odensass, P., 2014, Tagungsband AALE 2014: Das Forum für Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft, 11. Fachkonferenz, Regensburg. Regensburg: DIV Deutscher Industrieverlag GmbH, p. 221-230 10 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Transfer

  4. Residual stresses near the hot sprues of as-cast Mg-Zn alloys investigated by STRESS-SPEC neutron diffractometer

    Gan, W. M., Huang, Y. D., Wang, Z., Hort, N. & Hofmann, M., 2014, International Conference on Residual Stresses 9 (ICRS 9). Kurz, S. J. B., Mittemeijer, E. J. & Scholtes, B. (eds.). Trans Tech Publications Ltd, p. 428-432 5 p. (Materials Science Forum; vol. 768-769).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  5. Simulation of composite hot extrusion with high reinforcing Volumes

    Schwane, M., Citrea, T., Dahnke, C., Haase, M., Ben Khalifa, N. & Tekkaya, A. E., 2014, In: Procedia Engineering. 81, p. 1265-1270 6 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  6. Standort- und Netzwerkplanung in Metropolregionen: Aktueller Forschungsbedarf bei Entscheidungsmodellen

    Richter, L., Lübkemann, J., Schmidt, M. & Nyhuis, P., 2014, In: wt Werkstattstechnik online. 104, 4, p. 202-205 4 p.

    Research output: Journal contributions › Journal articles › Research

  7. Published

    Steady State Detection for the Context Aware Evaluation of Vital Signs

    Busch, B.-H. & Welge, R., 2014, Wohnen – Pflege – Teilhabe: Besser leben durch Technik - 7. AAL-Kongress mit Ausstellung 21.-22. Januar 2014 in Berlin, Tagungsbeiträge. VDE Verlag, 8 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  8. Strangpressen von Profilen mit variabler Wandstärke

    Selvaggio, A., Haase, M., Ben Khalifa, N. & Tekkaya, A. E., 2014, In: International Aluminium Journal. 90, 11, p. 49-51 3 p.

    Research output: Journal contributions › Journal articles › Research

  9. Published

    Using Euler Discrete Approximation to Control an Aggregate Actuator in Camless Engines

    Mercorelli, P. & Werner, N., 2014, In: International Journal of Mathematical Models and Methods in Applied Sciences . 8, 1, p. 273-280 8 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  10. Thermodynamic assessment and experimental study of Mg-Gd alloys

    Hampl, M., Blawert, C., Silva Campos, M. R., Hort, N., Peng, Q., Kainer, K. U. & Schmid-Fetzer, R., 25.12.2013, In: Journal of Alloys and Compounds. 581, p. 166-177 12 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  11. Effect of calcium addition on the hot working behavior of as-cast AZ31 magnesium alloy

    Suresh, K., Rao, K. P., Prasad, Y. V. R. K., Hort, N. & Kainer, K. U., 20.12.2013, In: Materials Science and Engineering A. 588, p. 272-279 8 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  12. Bulk and local textures of pure magnesium processed by rotary swaging

    Gan, W. M., Huang, Y. D., Wang, R., Zhong, Z. Y., Hort, N., Kainer, K. U., Schell, N., Brokmeier, H. G. & Schreyer, A., 01.12.2013, In: Journal of Magnesium and Alloys. 1, 4, p. 341-345 5 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  13. Compressive strength and hot deformation mechanisms in as-cast Mg-4Al-2Ba-2Ca (ABaX422) alloy

    Rao, K. P., Ip, H. Y., Suresh, K., Prasad, Y. V. R. K., Wu, C. M. L., Hort, N. & Kainer, K. U., 01.12.2013, In: Philosophical Magazine. 93, 35, p. 4364-4377 14 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  14. Application of non-convex rate dependent gradient plasticity to the modeling and simulation of inelastic microstructure development and inhomogeneous material behavior

    Klusemann, B., Yalçinkaya, T., Geers, M. G. D. & Svendsen, B., 12.2013, In: Computational Materials Science. 80, p. 51-60 10 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  15. Microstructure and mechanical properties of as-cast Mg-Sn-Ca alloys and effect of alloying elements

    Suresh, K., Rao, K. P., Prasad, Y. V. R. K., Hort, N. & Kainer, K. U., 12.2013, In: Transactions of Nonferrous Metals Society of China (English Edition). 23, 12, p. 3604-3610 7 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  16. Maschinen- und werkzeugseitige Herausforderungen bei der Blechmassivumformung von komplexen Bauteilen

    Salfeld, V., Matthias, T., Krimm, R., Behrens, B.-A., Sieczkarek, P., Ben Khalifa, N., Tekkaya, A. E., Hetzner, H., Tremmel, S. & Wartzack, S., 13.11.2013, Tagungsband zum 2. Erlanger Workshop Blechmassivumformung 2013: 2. Workshop Blechmassivumformung. Merklein, M., Behrens, B. A. & Tekkaya, A. E. (eds.). Meisenbach Verlag, p. 13-35 23 p.

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  17. Comparison of different in vitro tests for biocompatibility screening of Mg alloys

    Scheideler, L., Füger, C., Schille, C., Rupp, F., Wendel, H. P., Hort, N., Reichel, H. P. & Geis-Gerstorfer, J., 11.2013, In: Acta Biomaterialia. 9, 10, p. 8740-8745 6 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  18. Element distribution in the corrosion layer and cytotoxicity of alloy Mg-10Dy during in vitro biodegradation

    Yang, L., Hort, N., Laipple, D., Höche, D., Huang, Y., Kainer, K. U., Willumeit, R. & Feyerabend, F., 11.2013, In: Acta Biomaterialia. 9, 10, p. 8475-8487 13 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  19. Fast escape of hydrogen from gas cavities around corroding magnesium implants

    Kuhlmann, J., Bartsch, I., Willbold, E., Schuchardt, S., Holz, O., Hort, N., Höche, D., Heineman, W. R. & Witte, F., 11.2013, In: Acta Biomaterialia. 9, 10, p. 8714-8721 8 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  20. Microstructure, mechanical and corrosion properties of Mg-Dy-Gd-Zr alloys for medical applications

    Yang, L., Huang, Y., Feyerabend, F., Willumeit, R., Mendis, C., Kainer, K. U. & Hort, N., 11.2013, In: Acta Biomaterialia. 9, 10, p. 8499-8508 10 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

Previous 1...61 62 63 64 65 66 67 68 ...94 Next

Recently viewed