1. //
  2. Start
  3. //
  4. Organisations
  5. //
  6. Professorship for Manufacturing – Innova...
  7. //
  8. Publications
  9. //

Professorship for Manufacturing – Innovative Manufacturing

Organisational unit: Section

Advanced search options
Advanced search options

Reset

to
31 - 40 out of 51Page size: 10
  1. 2022
  2. Published

    Geometrical Accuracy in Two-Stage Incremental Sheet Forming with Active Medium

    Thiery, S. & Ben Khalifa, N., 2022, Production at the Leading Edge of Technology: Proceedings of the 11th Congress of the German Academic Association for Production Technology (WGP), Dresden, September 2021. Behrens, B-A., Brosius, A., Drossel, W-G., Hintze, W., Ihlenfeldt, S. & Nyhuis, P. (eds.). Cham: Springer, p. 65-74 10 p. (Lecture Notes in Production Engineering; vol. Part F1160).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  3. Published

    Process Stability and Reproducibility of the Dieless Drawing Process for AZ31 Magnesium Wires

    Braatz, M., Bohlen, J. & Khalifa, N. B., 2022, Achievements and Trends in Material Forming: Peer-reviewed extended papers selected from the 25 th International Conference on Material Forming (ESAFORM 2022). Vincze, G. & Barlat, F. (eds.). Baech: Trans Tech Publications Ltd, p. 389-400 12 p. (Key Engineering Materials; vol. 926 ).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  4. 2021
  5. Published

    Closed-loop control of product geometry by using an artificial neural network in incremental sheet forming with active medium

    Thiery, S., Zein El Abdine, M., Heger, J. & Ben Khalifa, N., 01.11.2021, In: International Journal of Material Forming. 14, 6, p. 1319–1335 17 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  6. Published

    Experimental Setup of Dieless Drawing Process for Magnesium Wire

    Braatz, M., Dieckmann, A., Bohlen, J. & Ben Khalifa, N., 05.09.2021, Production at the Leading Edge of Technology: Proceedings of the 11th Congress of the German Academic Association for Production Technology (WGP), Dresden 2021. Behrens, B-A., Brosius, A., Drossel, W-G., Hintze, W., Ihlenfeldt, S. & Nyhuis, P. (eds.). Cham: Springer Nature Switzerland AG, p. 38-46 9 p. (Lecture Notes in Production Engineering; vol. Part F1160).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  7. Published

    Homogenization of the interfacial bonding of compound-cast AA7075/6060 bilayer billets by co-extrusion

    Chen, H., Giannopoulou, D., Greß, T., Isakovic, J., Mittler, T., Volk, W. & Ben Khalifa, N., 09.2021, In: International Journal of Material Forming. 14, 5, p. 1109-1119 11 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  8. Published

    Entscheidungsbäume und bestärkendes Lernen zur dynamischen Auswahl von Reihenfolgeregeln in einem flexiblen Produktionssystem

    Heger, J., Zein El Abdine, M., Sekar, S. & Voß, T., 26.08.2021, Simulation in Produktion und Logistik 2021: Erlangen, 15. - 17. September 2021. Franke, J. & Schuderer, P. (eds.). Göttingen: Cuvillier Verlag, p. 337-346 10 p. (ASIM-Mitteilung; vol. AM 177).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  9. Published

    Outperformed by a Computer? - Comparing Human Decisions to Reinforcement Learning Agents, Assigning Lot Sizes in a Learning Factory: 11th Conference on Learning Factories, CLF2021

    Voß, T., Rokoss, A., Maier, J. T., Schmidt, M. & Heger, J., 06.2021, Rochester: Elsevier Inc., 6 p. (SSRN).

    Research output: Working paper › Working papers

  10. Published

    Introducing Residual Stresses on Sheet Metals by Slide Hardening under Stress Superposition

    Lehmann, J., Chen, H., Kruse, M. & Ben Khalifa, N., 27.04.2021, In: Key Engineering Materials. 883, p. 143-150 8 p.

    Research output: Journal contributions › Conference article in journal › Research › peer-review

  11. Published

    Co-extrusion of compound-cast AA7075/6060 bilayer billets at various temperatures

    Chen, H., Giannopoulou, D., Greß, T., Mittler, T., Isakovic, J., Volk, W. & Ben Khalifa, N., 2021, Forming the Future - Proceedings of the 13th International Conference on the Technology of Plasticity. Daehn, G., Cao, J., Kinsey, B., Teekaya, E., Vivek, A. & Yoshida, Y. (eds.). Cham: Springer International Publishing AG, p. 993-1001 9 p. (Minerals, Metals and Materials Series).

    Research output: Contributions to collected editions/works › Article in conference proceedings › Research › peer-review

  12. Published

    Dynamische Losgrößenoptimierung mit bestärkendem Lernen

    Voß, T., Bode, C. & Heger, J., 2021, In: ZWF Zeitschrift für wirtschaftlichen Fabrikbetrieb. 116, 11, p. 815-819 5 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

Previous 1 2 3 4 5 6 Next