1. //
  2. Start
  3. //
  4. Journals
  5. //
  6. Materials Science and Engineering A
  7. //
  8. Publications
  9. //

Materials Science and Engineering A, ‎0921-5093

Journal

31 - 40 out of 40Page size: 10

  1. Effect of calcium addition on the hot working behavior of as-cast AZ31 magnesium alloy

    Suresh, K., Rao, K. P., Prasad, Y. V. R. K., Hort, N. & Kainer, K. U., 20.12.2013, In: Materials Science and Engineering A. 588, p. 272-279 8 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  2. Effect of die design on the welding quality during solid state recycling of AA6060 chips by hot extrusion

    Güley, V., Güzel, A., Jäger, A., Ben Khalifa, N., Tekkaya, A. E. & Misiolek, W. Z., 01.07.2013, In: Materials Science & Engineering A. 574, p. 163-175 13 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  3. Hot deformation behavior of Mg-2Sn-2Ca alloy in as-cast condition and after homogenization

    Rao, K. P., Prasad, Y. V. R. K., Suresh, K., Hort, N. & Kainer, K. U., 30.08.2012, In: Materials Science and Engineering A. 552, p. 444-450 7 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  4. Improving mechanical properties of chip-based aluminum extrudates by integrated extrusion and equal channel angular pressing (iECAP)

    Haase, M., Ben Khalifa, N., Tekkaya, A. E. & Misiolek, W. Z., 30.03.2012, In: Materials Science & Engineering A. 539, p. 194-204 11 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  5. Compressive strength and hot deformation behavior of TX32 magnesium alloy with 0.4% Al and 0.4% Si additions

    Rao, K. P., Prasad, Y. V. R. K., Dharmendra, C., Hort, N. & Kainer, K. U., 25.08.2011, In: Materials Science and Engineering A. 528, 22-23, p. 6964-6970 7 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  6. Effect of yttrium addition on lattice parameter, Young's modulus and vacancy of magnesium

    Peng, Q., Meng, J., Li, Y., Huang, Y. & Hort, N., 25.02.2011, In: Materials Science and Engineering A. 528, 4-5, p. 2106-2109 4 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  7. Optimum parameters and rate-controlling mechanisms for hot working of extruded Mg-3Sn-1Ca alloy

    Prasad, Y. V. R. K., Rao, K. P., Hort, N. & Kainer, K. U., 25.02.2009, In: Materials Science and Engineering A. 502, 1-2, p. 25-31 7 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  8. Investigation of minimum creep rates and stress exponents calculated from tensile and compressive creep data of magnesium alloy AE42

    Dieringa, H., Hort, N. & Kainer, K. U., 15.06.2009, In: Materials Science and Engineering A. 510-511, C, p. 382-386 5 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  9. Creep behavior of AE42 based hybrid composites

    Arunachaleswaran, A., Pereira, I. M., Dieringa, H., Huang, Y., Hort, N., Dhindaw, B. K. & Kainer, K. U., 15.07.2007, In: Materials Science and Engineering A. 460-461, p. 268-276 9 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  10. Tensile and compressive creep behaviour of Al2O3 (Saffil®) short fiber reinforced magnesium alloy AE42

    Dieringa, H., Huang, Y., Maier, P., Hort, N. & Kainer, K. U., 25.11.2005, In: Materials Science and Engineering A. 410-411, p. 85-88 4 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

Previous 1 2 3 4 Next

Recently viewed

Researchers

  1. Mayleen Luisa Schack