1. //
  2. Start
  3. //
  4. Journals
  5. //
  6. Journal of Materials Processing Technolo...
  7. //
  8. Publications
  9. //

Journal of Materials Processing Technology, ‎0924-0136

Journal

1 - 10 out of 13Page size: 10
Sort by: Title
  1. Published

    A multi-scaled process study of dissimilar friction stir welding of Eurofer RAFM steel to PM2000 ODS alloy

    Wang, J., Fu, B., Shen, J., Bergmann, L., Lu, X., dos Santos, J. F. & Klusemann, B., 01.09.2022, In: Journal of Materials Processing Technology. 307, 117679.

    Research output: Journal contributions › Journal articles › Research › peer-review

  2. Published

    Analytical prediction of wall thickness reduction and forming forces during the radial indentation process in Incremental Profile Forming

    Grzancic, G., Löbbe, C., Ben Khalifa, N. & Tekkaya, A. E., 05.2019, In: Journal of Materials Processing Technology. 267, p. 68-79 12 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  3. Published

    Effect of consumable stud microstructure on friction surfacing: Comparison between friction extruded and hot extruded AA2024 studs

    Aspes, P., Kallien, Z., Rath, L., Suhuddin, U. & Klusemann, B., 07.2025, In: Journal of Materials Processing Technology. 341, 14 p., 118862.

    Research output: Journal contributions › Journal articles › Research › peer-review

  4. Published

    Effect of laser peen forming process parameters on bending and surface quality of Ti-6Al-4V sheets

    Sala, S. T., Keller, S., Chupakhin, S., Pöltl, D., Klusemann, B. & Kashaev, N., 01.07.2022, In: Journal of Materials Processing Technology. 305, 16 p., 117578.

    Research output: Journal contributions › Journal articles › Research › peer-review

  5. Published

    Experimental and numerical investigation of residual stresses in laser shock peened AA2198

    Keller, S., Chupakhin, S., Staron, P., Maawad, E., Kashaev, N. & Klusemann, B., 01.05.2018, In: Journal of Materials Processing Technology. 255, p. 294-307 14 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  6. Granular media-based tube press hardening

    Chen, H., Güner, A., Ben Khalifa, N. & Tekkaya, A. E., 01.02.2016, In: Journal of Materials Processing Technology. 228, p. 145-159 15 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  7. Hot workability characteristics of cast and homogenized Mg-3Sn-1Ca alloy

    Rao, K. P., Prasad, Y. V. R. K., Hort, N. & Kainer, K. U., 26.05.2008, In: Journal of Materials Processing Technology. 201, 1-3, p. 359-363 5 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  8. Mechanics of sheet-bulk indentation

    Sieczkarek, P., Isik, K., Ben Khalifa, N., Martins, P. A. F. & Tekkaya, A. E., 11.2014, In: Journal of Materials Processing Technology. 214, 11, p. 2387-2394 8 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

  9. Published

    Microstructural development of as-cast AM50 during Constrained Friction Processing: grain refinement and influence of process parameters

    de Castro, C. C., Shen, J., dos Santos, J. F. & Klusemann, B., 01.09.2023, In: Journal of Materials Processing Technology. 318, 11 p., 118018.

    Research output: Journal contributions › Journal articles › Research

  10. Prediction of roughness after ball burnishing of thermally coated surfaces

    Hiegemann, L., Weddeling, C., Ben Khalifa, N. & Tekkaya, A. E., 03.2015, In: Journal of Materials Processing Technology. 217, p. 193-201 9 p.

    Research output: Journal contributions › Journal articles › Research › peer-review

Previous 1 2 Next

Recently viewed