Hot forging of cast magnesium alloy TX31 using semi-closed die and its finite element simulation

Publikation: Beiträge in SammelwerkenAufsätze in KonferenzbändenForschungbegutachtet

Authors

  • K. P. Rao
  • K. Suresh
  • Y. V.R.K. Prasad
  • N. Hort
  • K. U. Kainer

Magnesium alloys based on Mg-Sn-Ca system have shown improved corrosion and creep properties. In this type of alloys,Sn forms a solid solution with Mg that improves the corrosion resistance while Ca forms thermally stable intermetallic phases in the matrix enhancing the creep resistance. The Sn to Ca ratio is an important variable in deciding the type of intermetallic phases that form in the microstructure.In Mg-3Sn-1Ca alloy (TX31), a single intermetallic phase CaMgSnforms, which is responsible for its improved creep strength.With a view to evaluate its forgeability,isothermal forging experiments of TX31 were conducted on a hydraulic press in the temperature range of 350°C to 500°C and at speeds of 0.01 mm s-1to 10 mm s-1 using a semiclosed die. Finite-element (FE) simulation of the forging process was also conducted using the software DEFORM 2D to obtain the local variations of strain and strain rate. The effectivestrain values are below2.4 in the forged components and the forging loads predicted using FE simulation correlated well with the experimental data for all the forging conditions. The microstructures of the forgings show that CaMgSn phase is well distributed in the matrix which exhibited dynamically recrystallized microstructure as predicted by the processing map.

OriginalspracheEnglisch
TitelTHERMEC 2013
HerausgeberB. Mishra, Mihail. Ionescu, T. Chandra
Anzahl der Seiten6
VerlagTrans Tech Publications Ltd
Erscheinungsdatum05.2014
Seiten449-454
ISBN (Print)9783038350736
DOIs
PublikationsstatusErschienen - 05.2014
Extern publiziertJa
Veranstaltung8th International Conference on Processing and Manufacturing of Advanced Materials - THERMEC 2013 - Las Vegas, NV, USA / Vereinigte Staaten
Dauer: 02.12.201306.12.2013
Konferenznummer: 8

Zuletzt angesehen

Publikationen

  1. Forging of Mg–3Sn–2Ca–0.4Al Alloy Assisted by Its Processing Map and Validation Through Analytical Modeling
  2. CHANGING RECREATIONAL ACTIVITIES FOR REDUCING INSOMNIA SEVERITY? RESULTS FROM A SERIAL MEDIATION ANALYSIS ON THE IMPACT OF RECREATIONAL BEHAVIOR AS A MECHANISM OF CHANGE IN DIGITAL INTERVENTIONS FOR INSOMNIA
  3. Effect of yttrium addition on lattice parameter, Young's modulus and vacancy of magnesium
  4. Forging of cast Mg-3Sn-2Ca-0.4Al-0.4Si magnesium alloy using processing map
  5. As cast microstructures on the mechanical and corrosion behaviour of ZK40 modified with Gd and Nd additions
  6. Influence of Dy in solid solution on the degradation behavior of binary Mg-Dy alloys in cell culture medium
  7. Effect of erbium modification on the microstructure, mechanical and corrosion characteristics of binary Mg-Al alloys
  8. Effect of grain size and structure, solid solution elements, precipitates and twinning on nanohardness of Mg-Re alloys
  9. Acceleration as process
  10. Wavlet analysis for rotor fault diagnosis with rub-impact of rotor systems
  11. Microstructural and Mechanical Aspects of Reinforcement Welds for Lightweight Components Produced by Friction Hydro Pillar Processing
  12. Mechanical properties and microstructures of nano SiC reinforced ZE10 composites prepared with ultrasonic vibration
  13. Comparative study on corrosion behavior of we33 in immersion and polarization influenced by heat treatment
  14. Study of the solidification of AS alloys combining in situ synchrotron diffraction and differential scanning calorimetry
  15. Effect of internal defects on tensile properties of A356 casting alloys
  16. Empirical research on mathematical modelling
  17. Microstructure evolution of Mg-11Gd-4.5Y-1Nd-1.5Zn-0.5Zr (wt%) alloy during deformation and its effect on strengthening