Materials Science and Engineering A, ‎0921-5093

Fachzeitschrift: Zeitschrift

  1. 2005
  2. Tensile and compressive creep behaviour of Al2O3 (Saffil®) short fiber reinforced magnesium alloy AE42

    Dieringa, H., Huang, Y., Maier, P., Hort, N. & Kainer, K. U., 25.11.2005, in: Materials Science and Engineering A. 410-411, S. 85-88 4 S.

    Publikation: Beiträge in ZeitschriftenZeitschriftenaufsätzeForschungbegutachtet

  3. 2007
  4. Creep behavior of AE42 based hybrid composites

    Arunachaleswaran, A., Pereira, I. M., Dieringa, H., Huang, Y., Hort, N., Dhindaw, B. K. & Kainer, K. U., 15.07.2007, in: Materials Science and Engineering A. 460-461, S. 268-276 9 S.

    Publikation: Beiträge in ZeitschriftenZeitschriftenaufsätzeForschungbegutachtet

  5. 2009
  6. Optimum parameters and rate-controlling mechanisms for hot working of extruded Mg-3Sn-1Ca alloy

    Prasad, Y. V. R. K., Rao, K. P., Hort, N. & Kainer, K. U., 25.02.2009, in: Materials Science and Engineering A. 502, 1-2, S. 25-31 7 S.

    Publikation: Beiträge in ZeitschriftenZeitschriftenaufsätzeForschungbegutachtet

  7. Investigation of minimum creep rates and stress exponents calculated from tensile and compressive creep data of magnesium alloy AE42

    Dieringa, H., Hort, N. & Kainer, K. U., 15.06.2009, in: Materials Science and Engineering A. 510-511, C, S. 382-386 5 S.

    Publikation: Beiträge in ZeitschriftenZeitschriftenaufsätzeForschungbegutachtet

  8. 2010
  9. Characterization of grain microstructure development in the aluminum alloy EN AW-6060 during extrusion

    Kayser, T., Klusemann, B., Lambers, H. G., Maier, H. J. & Svendsen, B., 25.09.2010, in: Materials Science & Engineering A. 527, 24-25, S. 6568-6573 6 S.

    Publikation: Beiträge in ZeitschriftenZeitschriftenaufsätzeForschungbegutachtet

  10. 2011
  11. Effect of yttrium addition on lattice parameter, Young's modulus and vacancy of magnesium

    Peng, Q., Meng, J., Li, Y., Huang, Y. & Hort, N., 25.02.2011, in: Materials Science and Engineering A. 528, 4-5, S. 2106-2109 4 S.

    Publikation: Beiträge in ZeitschriftenZeitschriftenaufsätzeForschungbegutachtet

  12. Compressive strength and hot deformation behavior of TX32 magnesium alloy with 0.4% Al and 0.4% Si additions

    Rao, K. P., Prasad, Y. V. R. K., Dharmendra, C., Hort, N. & Kainer, K. U., 25.08.2011, in: Materials Science and Engineering A. 528, 22-23, S. 6964-6970 7 S.

    Publikation: Beiträge in ZeitschriftenZeitschriftenaufsätzeForschungbegutachtet

  13. 2012
  14. Improving mechanical properties of chip-based aluminum extrudates by integrated extrusion and equal channel angular pressing (iECAP)

    Haase, M., Ben Khalifa, N., Tekkaya, A. E. & Misiolek, W. Z., 30.03.2012, in: Materials Science & Engineering A. 539, S. 194-204 11 S.

    Publikation: Beiträge in ZeitschriftenZeitschriftenaufsätzeForschungbegutachtet

  15. Hot deformation behavior of Mg-2Sn-2Ca alloy in as-cast condition and after homogenization

    Rao, K. P., Prasad, Y. V. R. K., Suresh, K., Hort, N. & Kainer, K. U., 30.08.2012, in: Materials Science and Engineering A. 552, S. 444-450 7 S.

    Publikation: Beiträge in ZeitschriftenZeitschriftenaufsätzeForschungbegutachtet

  16. 2013
  17. Effect of die design on the welding quality during solid state recycling of AA6060 chips by hot extrusion

    Güley, V., Güzel, A., Jäger, A., Ben Khalifa, N., Tekkaya, A. E. & Misiolek, W. Z., 01.07.2013, in: Materials Science & Engineering A. 574, S. 163-175 13 S.

    Publikation: Beiträge in ZeitschriftenZeitschriftenaufsätzeForschungbegutachtet

Vorherige 1 2 3 4 Nächste

Zuletzt angesehen

Publikationen

  1. Guest editorial
  2. Quantum Chemical Calculation and Evaluation of Partition Coefficients for Classical and Emerging Environmentally Relevant Organic Compounds
  3. Mechanical performance optimization of similar thin AA 7075‐T6 sheets produced by refill friction stir spot welding
  4. Effects of pesticides on community structure and ecosystem functions in agricultural streams of three biogeographical regions in Europe
  5. Effekte inter-organisationaler Balanced Scorecards
  6. Comparative effectiveness of three versions of a stepped care model for insomnia differing in the amount of therapist support in internet-delivered treatment
  7. Democratic Horizons
  8. Managing Research Environments
  9. „Ist das dein Handy oder vibrierst du?“
  10. Intra-specific leaf trait responses to species richness at two different local scales
  11. Emotional Human-Machine Interaction: Cues from Facial Expressions
  12. Open Innovation Networks
  13. A Review on Higher Education for Sustainable Development - Looking Back and Moving Forward
  14. Making a difference by marking the difference
  15. Non-native populations of an invasive tree outperform their native conspecifics
  16. Current Trends in Environmental Cost Accounting - and its Interaction with Eco-Efficiency Performance Measurement and Indicators
  17. A Dual Kalman Filter to Identify Parameters of a Permanent Magnet Synchronous Motor
  18. DSM-IV und DSM-5
  19. DBLP-QuAD
  20. Frustrated and helpless - sources and consequences of students’ negative deactivating emotions in university mathematics
  21. Political discourse as mediated and public discourse
  22. Comparison of different FEM code approaches in the simulation of the die deflection during aluminium extrusion
  23. Terminologien/Semantik
  24. Differenz und Alterität im Ritual
  25. A qualitative approach to evidence-based entrepreneurship: Theoretical considerations and an example involving business clusters
  26. Orientierung im Realraum
  27. An Empirical Note on Religiosity and Social Trust using German Survey Data
  28. Taking Responsibility for Others and Use of Mental Contrasting