Materials Science and Engineering A, ‎0921-5093

Journal

  1. 2005
  2. Tensile and compressive creep behaviour of Al2O3 (Saffil®) short fiber reinforced magnesium alloy AE42

    Dieringa, H., Huang, Y., Maier, P., Hort, N. & Kainer, K. U., 25.11.2005, In: Materials Science and Engineering A. 410-411, p. 85-88 4 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  3. 2007
  4. Creep behavior of AE42 based hybrid composites

    Arunachaleswaran, A., Pereira, I. M., Dieringa, H., Huang, Y., Hort, N., Dhindaw, B. K. & Kainer, K. U., 15.07.2007, In: Materials Science and Engineering A. 460-461, p. 268-276 9 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  5. 2009
  6. Optimum parameters and rate-controlling mechanisms for hot working of extruded Mg-3Sn-1Ca alloy

    Prasad, Y. V. R. K., Rao, K. P., Hort, N. & Kainer, K. U., 25.02.2009, In: Materials Science and Engineering A. 502, 1-2, p. 25-31 7 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  7. Investigation of minimum creep rates and stress exponents calculated from tensile and compressive creep data of magnesium alloy AE42

    Dieringa, H., Hort, N. & Kainer, K. U., 15.06.2009, In: Materials Science and Engineering A. 510-511, C, p. 382-386 5 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  8. 2010
  9. Characterization of grain microstructure development in the aluminum alloy EN AW-6060 during extrusion

    Kayser, T., Klusemann, B., Lambers, H. G., Maier, H. J. & Svendsen, B., 25.09.2010, In: Materials Science & Engineering A. 527, 24-25, p. 6568-6573 6 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  10. 2011
  11. Effect of yttrium addition on lattice parameter, Young's modulus and vacancy of magnesium

    Peng, Q., Meng, J., Li, Y., Huang, Y. & Hort, N., 25.02.2011, In: Materials Science and Engineering A. 528, 4-5, p. 2106-2109 4 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  12. Compressive strength and hot deformation behavior of TX32 magnesium alloy with 0.4% Al and 0.4% Si additions

    Rao, K. P., Prasad, Y. V. R. K., Dharmendra, C., Hort, N. & Kainer, K. U., 25.08.2011, In: Materials Science and Engineering A. 528, 22-23, p. 6964-6970 7 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  13. 2012
  14. Improving mechanical properties of chip-based aluminum extrudates by integrated extrusion and equal channel angular pressing (iECAP)

    Haase, M., Ben Khalifa, N., Tekkaya, A. E. & Misiolek, W. Z., 30.03.2012, In: Materials Science & Engineering A. 539, p. 194-204 11 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  15. Hot deformation behavior of Mg-2Sn-2Ca alloy in as-cast condition and after homogenization

    Rao, K. P., Prasad, Y. V. R. K., Suresh, K., Hort, N. & Kainer, K. U., 30.08.2012, In: Materials Science and Engineering A. 552, p. 444-450 7 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

  16. 2013
  17. Effect of die design on the welding quality during solid state recycling of AA6060 chips by hot extrusion

    Güley, V., Güzel, A., Jäger, A., Ben Khalifa, N., Tekkaya, A. E. & Misiolek, W. Z., 01.07.2013, In: Materials Science & Engineering A. 574, p. 163-175 13 p.

    Research output: Journal contributionsJournal articlesResearchpeer-review

Previous 1 2 3 4 Next